Adaptation To Different Types Of Gas - Elica NIKOLATESLA FLAME Montage- Und Gebrauchsanweisungen

Never use a flame to perform this check.
● Adaptation to different types of gas ●
To adapt the appliance to a type of gas
other than that for which it is designed (as
indicated on the label fixed to the lower part
of the hob or the packaging), the burner
nozzles must be replaced by performing
the following operations: ● 1 - remove the
stove top grids and remove the burners
from their slots ● 2 - unscrew the nozzles,
using a 7mm socket wrench and replace
them with ones suitable for the new type of
gas (see table "Characteristics of gas
burners") ● 3 - reassemble the parts
following the steps in reverse order ●
Warning! At the end of the operation,
replace the old calibration label with the
one for the new gas used.FIG.A0.
● Minimum adjustment ● For minimum
adjustment: ● 1 - turn the tap to the
minimum setting ● 2- remove the knob and
adjust the screw located inside or next to
the valve shaft, with a suitable screwdriver,
until a small regular flame is obtained
FIG.A01 ● 3 - check that by turning the
knob quickly, from maximum to minimum,
the burners do not turn off ● 4 - if the safety
device fails (thermocouple), with the
burners on minimum setting, increase the
minimum flow rate by adjusting the relevant
screw. ● 5 - once the adjustment has been
made, re-seal the seals on the by-pass with
sealing wax or equivalent materials ● In
the case of liquid gases (e.g. LPG), the
adjustment screw must be screwed in
completely. ● Warning! At the end of the
operation, replace the old calibration label
with the one for the new gas used. ●
Warning! If the pressure of the gas used is
different (or variable) from that the one
indicated, an appropriate pressure
regulator on the inlet pipe must be installed
that complies with the national standards in
force. ● The amount of air required for
combustion must not be less than 2.0
m3/h for each kW of installed power.
See the table for the burner power.
3.3 Mounting
Before starting the installation:
• After unpacking the product, check that it has not been
damaged during transport and in the event of problem,
please contact the reseller or the Customer support
service before installing it.
• Check that the product is the right size for the installation
area.
• Check for accessories (e.g. bags containing screws, warranty
certificates, etc.) inside the packaging (placed there for
transport reasons). Remove and keep them safe, if present.
• Also check that there is a power socket near the installation
area.
Preparing the cabinet for installation:
- The product cannot be installed above cooling appliances,
dishwashers, heaters, ovens, washing machines and dryers.
- Create the cut-outs in the cabinet before inserting the hob and
carefully remove any shavings or sawdust.
IMPORTANT: use a single-component adhesive sealant (S),
which withstands temperatures up to 250°; before installation,
thoroughly clean the surfaces to stick and eliminate any
substance that may compromise adhesion, (e.g. release
agents, preservatives, fats, oil, dust, traces of old adhesives,
etc.); the adhesive should be uniformly spread all around the
outside of the frame; after sticking, leave the adhesive to dry
for about 24 hours.
Fig. 1b
Caution! Failure to install screws and
fasteners in accordance with these
instructions may result in electrical hazards.
Note: to ensure the correct installation of the product, it is
recommended to tape the pipes using an adhesive with the
following characteristics:
- soft elastic PVC film, with an acrylic-based adhesive
- which complies with DIN EN 60454 regulations
- self-extinguishing
- excellent resistance against wear
- resistant against temperature fluctuations
- can be used in low temperatures
20