Accessories - Makita 5604R Betriebsanleitung

Hold the tool firmly. The tool is provided with both a front
grip and rear handle. Use both to best grasp the tool. If
both hands are holding saw, they cannot be cut by the
blade. Set the base on the workpiece to be cut without
the blade making any contact. Then turn the tool on and
wait until the blade attains full speed. Now simply move
the tool forward over the workpiece surface, keeping it
flat and advancing smoothly until the sawing is
completed.
To get clean cuts, keep your sawing line straight and your
speed of advance uniform. If the cut fails to properly fol-
low your intended cut line, do not attempt to turn or force
the tool back to the cut line. Doing so may bind the blade
and lead to dangerous kickback and possible serious
injury. Release switch, wait for blade to stop and then
withdraw tool. Realign tool on a new cut line, and start
cut again. Attempt to avoid positioning which exposes
operator to chips and wood dust being ejected from saw.
Use eye protection to help avoid injury.
CAUTION:
• The riving knife should always be used except when
plunging in the middle of the workpiece.
Rip fence (Guide rule) (Fig. 17)
The handy rip fence allows you to do extra-accurate
straight cuts. Simply slide the rip fence up snugly against
the side of the workpiece and secure it in position with
the screw on the front of the base. It also makes
repeated cuts of uniform width possible.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
Replacing carbon brushes (Fig. 18 & 19)
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.

ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita service center.
• Saw blades
• Rip fence (Guide rule)
• Hex wrench
8
All manuals and user guides at all-guides.com
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745:
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
• The declared vibration emission value has been mea-
• The declared vibration emission value may also be
WARNING:
• The vibration emission during actual use of the power
• Be sure to identify safety measures to protect the oper-
We
manufacturer declare that the following Makita
machine(s):
Designation of Machine: Circular Saw
Model No./ Type: 5604R
are of series production and
Conforms to the following European Directives:
And are manufactured in accordance with the following
standards or standardised documents:
The technical documentation is kept by our authorized
representative in Europe who is:
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
Wear ear protection.
Work mode: cutting chipboard
Vibration emission (a
Uncertainty (K): 1.5 m/s
sured in accordance with the standard test method and
may be used for comparing one tool with another.
used in a preliminary assessment of exposure.
tool can differ from the declared emission value
depending on the ways in which the tool is used.
ator that are based on an estimation of exposure in the
actual conditions of use (taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to
the trigger time).
EC Declaration of Conformity
Makita Corporation
98/37/EC until 28th December 2009 and then with
2006/42/EC from 29th December 2009
EN60745
Makita International Europe Ltd.
Michigan Drive, Tongwell,
Milton Keynes, MK15 8JD, England
30th January 2009
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, JAPAN
ENG102-2
): 93 dB (A)
pA
): 104 dB (A)
wA
ENG214-2
2
or less
): 2.5 m/s
h
2
ENG901-1
ENH101-12
as the responsible