Inhaltsverzeichnis
Werbung
Light
•
LED & RGB, LED ON/OFF. Short press light mode button to switch light states.
Multimedia (FM/USB/BT)
•
Short press multimedia button, to switch Bluetooth or FM.
•
Corresponding indicator icon will light up under different mode. Every mode can be used independently. Bluetooth can connect phone, play music,
'
answer/reject (or hang up) the phone, call back Bluetooth phone; FM can play radio show.
•
Short press Pause/Recovery button to pause or recovery the current multimedia music.
FM
•
Under FM mode, FM indicator icon light up green. Pressing last track (or last show) and next track (or next show) button at the same time for 3s, can
search FM show. Every time when searching a show successfully, it will pause for a moment. It will play first show after searching finished. Displayer will
show the frequency.
•
Short press last track (or last show) button, to switch to last music or show
•
Short press next track (or next show) button, to switch to next music or show
VOLUME
•
Short press volume + or - button, to set up required volume. Long press can adjust quickly.
Bluetooth
•
Under Bluetooth mode, Bluetooth indicator icon light up blue.
•
Open equipment with Bluetooth function, search the equipment, find LEKING in list of available equipment then Click to match. After matching
successfully, open music player in the equipment, the standard control panel can play music which is sent from Bluetooth equipment.
•
When no call in, indicator light of Bluetooth phone is off. If long press this button at this moment, the latest phone call will be called back; When there's
call in, Bluetooth indicator icon light up green, and switch to Bluetooth mode automatically. At this moment, short press for 1s can answer Bluetooth
phone; long press for 3s can reject or hang up the Bluetooth phone.
Remote Control
•
To turn on the LED light press the light power button. To initiate RGB chromo therapy press the centre button located within the colour spectrum circle;
select desired colour on this circle. To increase the brightness press LIGHT and to decrease press DARK. Note! The sauna must be turned on to change
the colour of the LED light.
•
If your goal in your sauna use is detoxification, press DETOX. This will initiate a 30-minute session with a temperature hovering close to the maximum
temperature of 140F to induce perspiration to purge toxins from your body.
•
If your goal in your sauna is for general health, press HEALTH. This will initiate a 45-minute session with a temperature hovering at 115F to promote
muscle and joint relief and relaxation.
Dark
Light
Troubleshooting
On
Off
Problem
Health
Detox
No display on the control panel
Dark
Light
On
Off
Infrared heater can't be heated
Health
Detox
Sauna smells
Light does not work
Speaker problems
Sauna does not work
Control panel display "E1", the
buzzer alarm
Control panel display "E2", the
buzzer alarm
Control panel display "E3" the
buzzer alarm
Audio device does not work
Possible reasons
•
The cable is not connected
•
No power input
•
The control panel circuit board is broken
•
The heater is broken
•
The power connector of the heater is loose
•
Temperature sensor is broken
•
The fuse on the control box is damaged
•
The circuit board of the relay does not run
•
There is a foreign matter near the infrared heating element
•
The temperature of some infrared heater is too high
•
There is a device on the circuit board burned
•
The line is not connected
•
The light is broken
•
The electronic transformer is broken
•
Speaker line loose
•
Speaker damage
•
The socket is not plugged in
•
No power in the socket
•
Sauna transformer or circuit board failure
•
Temperature sensor open circuit failure (no detection of NTC) •
•
Temperature sensor short circuit
•
The temperature sensor monitors the temperature below
-15°C
•
The power cable on the roof is not connected
•
The signal cable is not connected or loosened
•
Audio equipment is damaged
Solutions
•
Check the cable interface or replace it
•
Check the circuit (focus on whether the power switch is
turned on)
•
Replace the corresponding circuit board
•
Replace the same type of a new heater
•
Check and keep them tight
•
Check if the sensor interface is loose or replace it
•
Replace the fuse
•
Replace the circuit board
•
Remove foreign matter
•
Disconnect the power supply and replace the heater
•
Replace the circuit board
•
Reconnect it
•
Replace a new light
•
Replace a new electronic transformer
•
Reconnect it
•
Replace a new speaker
•
Plug in the socket
•
Check the socket or line
•
Replace the sauna transformer or the associated circuit board
Shut down the system, restart to do the test again
•
Shut down the system, restart to do the test again
•
Shut down the system, restart to do the test again
•
Connect the power connection on the roof
•
Check and reconnect it
•
Replace a new audio device
Operating Instructions
EN
33
Werbung
Inhaltsverzeichnis
