Data Transfer - Bosch GTC 400 C Professional Originalbetriebsanleitung

internal memory of the measuring tool, press the "Save"
button (11).
Calling Up Saved Images
Proceed as follows to call up saved thermal images:
– Press the left-hand function button (13). The most re-
cently saved photo now appears in the display.
– Press the right-hand (8) or left-hand (12) arrow button to
switch between the saved thermal images.
You can also display the thermal image taken as a full-screen
image by pressing on the up arrow button (5).
Deleting saved images
Change to the gallery view to delete individual thermal im-
ages:
– Press the right-hand function button (7) under the waste
paper basket symbol.
– Confirm the process by pressing the left-hand function
button (13) or cancel the deletion by pressing the right-
hand function button (7).
<Delete All Images>
In the <Delete All Images> menu, you can delete all the files
in the internal memory at the same time. Press the Func (6)
button to call up the measuring functions. Now press the
right-hand function button (7) and select <Tool> → <Delete
All Images>. Press the right-hand arrow button (8) to enter
this submenu. Then press either the left-hand function
button (13) to delete all files, or the right-hand function
button (7) to cancel.

Data Transfer

Data Transfer via USB Port
Open the cover on the micro USB port (3). Connect the mi-
cro USB port (4) of the measuring tool to your computer via
the micro USB cable (24) provided.
Now press the on/off button (9) to switch on the measuring
tool.
Open the file browser on your computer and select the
GTC_400C drive. The saved files can be copied from the in-
ternal memory of the measuring tool, moved to your com-
puter or deleted.
As soon as you have finished the required operation, discon-
nect the drive from the computer following the standard pro-
cedure and then use the on/off button (9) to switch the
measuring tool off again.
Errors – Causes and Corrective Measures
In the event of a fault, the measuring tool will restart and can then continue to be used. If the fault persists, the following over-
view may help you.
Error Cause
Measuring tool cannot be Battery pack or batteries
switched on. empty
Battery pack too hot or too
cold
Bosch Power Tools
Caution: Always disconnect the drive from your operating
system first (eject drive), as failure to do so may damage the
internal memory of the measuring tool.
Remove the micro USB cable during the measurement oper-
ation and close the cover (3).
Always keep the flap of the USB port closed so that dust and
splashes cannot enter the housing.
Note: Use USB to connect the measuring tool to a computer
only. The measuring tool may be damaged if connected to
other devices.
Post-Editing the Thermal Images
You can post-edit the saved thermal images on your com-
puter if it uses a Windows operating system. To do so, down-
load the GTC Transfer software from the product page for
the measuring tool at
www.bosch-professional.com/thermal.
Data transmission via WLAN
The measuring tool is equipped with a Wi‑Fi® interface which
enables the saved images taken by your measuring tool to be
wirelessly transmitted to a mobile device.
Special Bosch applications (apps) are available for this use.
They can be downloaded in the store corresponding to your
device:
In addition to the wireless data transfer of your images, the
Bosch applications make it possible for you to use an exten-
ded range of functions and make it easier to post-edit and
forward measured data (e.g. via e-mail). Information about
system requirements for a Wi‑Fi® connection can be found
on the Bosch website at
www.bosch-professional.com/thermal.
To activate or deactivate the Wi‑Fi® connection on the meas-
uring tool, call up the main menu, use the buttons to
select <WiFi> and activate or deactivate it. The indicator (d)
appears in the display when the Wi‑Fi® is activated. Ensure
that the Wi‑Fi® interface is activated on your mobile device.
The connection between the mobile device and the measur-
ing tool can be established after the Bosch application has
been started (if the Wi‑Fi® modules are activated). To do
this, follow the instructions in the application (app).
Corrective measure
Charge the battery pack or change the batteries.
Allow the battery pack to reach the correct temperature or
change it.
English | 23
1 609 92A 7L1 | (20.05.2022)