Data Transfer - Bosch GTC 600 C Professional Originalbetriebsanleitung

When recording, please note the following:
– The microphone (15) is located behind the keyboard next
to the microphone symbol. Speak in the direction of the
microphone.
– The recording can last a maximum of 30 seconds.
Calling Up Saved Images
Proceed as follows to call up saved thermal images:
– Press the left-hand function button (16). The most re-
cently saved photo now appears in the display.
– Press the right-hand (10) or left-hand (14) arrow button
to switch between the saved thermal images.
The visual image has been saved alongside the thermal im-
age. To call up the visual image, press the down arrow
button (12).
You can also display the thermal image taken as a full-screen
image by pressing on the up arrow button (7). In the full-
screen view, the title bar is hidden after 3 seconds so that
you can see all the details of the thermal image.
You can use the up arrow button (7) and the down arrow
button (12) to switch between views.
Deleting Saved Images and Voice Notes
Switch to the gallery view to delete individual or all thermal
images:
– Press the right-hand function button (9) under the waste
paper basket symbol. A submenu will open. Here you can
select whether you want to delete only this image, only
the corresponding voice note (if you have recorded one)
or all images. If you want to delete only this image or the
voice note, confirm the process by pressing the Func (8)
button.
– If you want you delete all images, press the Func (8) but-
ton or the right-hand function button (9); you can also
confirm the process by pressing the right-hand function
button (9) or cancel the deletion by pressing the left-
hand function button (16).
Data fragments of the images remain stored in the memory
and could be reconstructed. You can
select <Tool> → <Factory settings> in the main menu to
permanently delete.

Data Transfer

Data Transfer via USB Port
Open the flap for the USB Type-C® port (5). Connect the
USB Type-C® port (6) of the measuring tool to your com-
puter via the USB Type-C® cable (25) provided.
Now press the on/off button (11) to switch on the measuring
tool.
Open the file browser on your computer and select the
GTC 600 C drive. The saved files can be copied from the in-
Errors – Causes and Corrective Measures
In the event of a fault, the measuring tool will restart and can then continue to be used. If the fault persists, the following over-
view may help you.
Bosch Power Tools
ternal memory of the measuring tool, moved to your com-
puter or deleted.
As soon as you have finished the required operation, discon-
nect the drive from the computer following the standard pro-
cedure and then use the on/off button (11) to switch the
measuring tool off again.
Caution: Always disconnect the drive from your operating
system first (eject drive), as failure to do so may damage the
internal memory of the measuring tool.
Remove the USB Type-C® cable during the measuring opera-
tion and close the flap (5).
Always keep the flap of the USB port closed so that dust and
splashes cannot enter the housing.
Note: Use USB to connect the measuring tool to a computer
only. The measuring tool may be damaged if connected to
other devices.
Note: The USB Type-C® interface can only be used for data
transfer. It is not suitable for charging non-rechargeable and
rechargeable batteries.
Post-Editing the Thermal Images
You can post-edit the saved thermal images on your com-
puter if it uses a Windows operating system. To do so, down-
load the GTC Transfer software from the product page for
the measuring tool at
www.bosch-professional.com/thermal.
Data transmission via Wi-Fi
The measuring tool is equipped with a Wi-Fi interface which
enables the saved images taken by your measuring tool to be
wirelessly transmitted to a mobile device.
Special Bosch applications (apps) are available for this use.
They can be downloaded in the store corresponding to your
device:
In addition to the wireless data transfer of your images, the
Bosch applications make it possible for you to use an exten-
ded range of functions and make it easier to post-edit and
forward measured data (e.g. via e-mail). Information about
system requirements for a Wi-Fi connection can be found on
the Bosch website at www.bosch‑professional.com/thermal.
To activate or deactivate the Wi-Fi connection on the meas-
uring tool, call up the main menu, use the buttons to
select <WiFi> and activate or deactivate it. The indicator (e)
appears in the display when the Wi-Fi is activated. Ensure
that the Wi-Fi interface is activated on your mobile device.
The connection between the mobile device and the measur-
ing tool can be established after the Bosch application has
been started (if Wi-Fi modules are activated). To do this, fol-
low the instructions in the application (app).
English | 23
1 609 92A 4UF | (14.01.2021)