Herunterladen Inhalt Inhalt Diese Seite drucken

Cleaning And Maintenance - Scheppach 5906807901 Original Bedienungsanleitung

Ständerbohrmaschine
Vorschau ausblenden Andere Handbücher für 5906807901:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
Electrical connection cables must comply with the ap-
plicable VDE and DIN provisions. Only use connection
cables with designation H05VV-F.
The printing of the type designation on the connection
cable is mandatory.
AC motor
• The mains voltage must be 230 V~
• Extension cables up to 25 m long must have a
cross-section of 1.5 square millimetres.
Connections and repair work on the electrical equip-
ment may only be carried out by electricians.
Please provide the following information in the event
of any enquiries:
• Type of current for the motor
• Machine data - type plate
• Motor data - type plate

11. Cleaning and maintenance

Pull out the mains plug before carrying out any
adjustments, maintenance or repair work.
m Have tasks that are not described in this operat-
ing manual, carried out by a specialist workshop.
Use only original parts. Let the device cool down
before all maintenance and cleaning tasks. There
is a risk of burns!
Before using the device each time, check the device
for obvious defects such as worn or damaged parts,
correct seating of screws or other parts. Replace dam-
aged parts.
Cleaning
Do not use cleaning agents or solvents. Chemical sub-
stances could damage the plastic parts of the device.
Never clean the device under running water.
Clean the device thoroughly after each use.
Clean the ventilation holes and the surface of the
device with a soft brush or cloth.
Remove chips, dust and dirt with a vacuum clean-
er if necessary.
Lubricate the moving parts regularly.
Do not allow lubricants to get onto switches,
V-belts, drive pulleys and drill stroke arms.
Maintenance
Setting the laser, fig. 23 + 24
Clamp a drill bit in the chuck (12). The laser forms a
crosshair in the centre of the drill. If the laser line does
not meet in the centre of the drill, the laser must be
adjusted.
Position the drilling table (4) as close as possible to the
drill. Loosen the locknuts (G). It is possible to adjust
the laser lines by turning the adjustment screws (H) on
both sides.
Set the laser lines such that they cross in the middle
of the drill tip.
Adjusting the spindle retaining spring, Fig. 25
It may be necessary for the spindle retaining spring to
be adjusted because of changed tension, making the
spindle return too quickly or too slowly.
1.
To provide more space, lower the table.
2.
Work on the left side of the drill.
3.
Put a screwdriver in the front lower notch (L), keep-
ing it in place.
4.
Remove the outer locknut (O) with a flat spanner
(SW19).
5.
Leaving the screwdriver in the notch, loosen the
inner locknut (N) until the cut-out (K) is released
from the boss (P). WARNING! Spring is under
tension!
6.
Using the screwdriver, carefully turn the spring cap
(M) anti-clockwise until you can press the notch
into the boss (P).
7.
Lower the spindle to the lowest position and hold
the spring cap (M) in place. When the spindle
moves up and down as desired, retighten the inner
locknut (N).
8.
If it is too loose, repeat steps 3-5. If it is too tight,
repeat in reverse order.
9.
Using a flat spanner, tighten the outer locknut (O)
against the inner locknut (N).
NOTE: Do not over-tighten and do not restrict the
movement of the spindle!
Service information
With this product, it is necessary to note that the fol-
lowing parts are subject to natural or usage-related
wear, or that the following parts are required as con-
sumables.
Wearing parts*:Carbon brushes; V-belts, drill
* may not be included in the scope of supply!
www.scheppach.com
GB | 33

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Dp18vario

Inhaltsverzeichnis