Ec Declaration Of Conformity; Safety Warnings - Makita AN454 Betriebsanleitung

WARNING:
The vibration emission during
actual use of the po w er tool can differ from the
declared value ( s ) depending on the w ays in w hich
the tool is used especially w hat kind of w orkpiece
is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use ( taking account of all parts of the operating
cycle such as the times w hen the tool is s w itched
off and w hen it is running idle in addition to the
trigger time ) .

EC Declaration of Conformity

For European countries only
T h e E C d e c laration o f c on f ormit y is in c lu d e d as A nne x A
to t h is instru c tion manual.
SAFETY W ARNINGS
Pneumatic nailer/stapler safety
w arnings
WARNING:
Read all safety w arnings and
all instructions. F ailure to f ollo w t h e w arnings an d
instru c tions ma y result in serious in j ur y , ele c tri c s h o c k
and/or fire.
Save all w arnings and instruc-
tions for future reference.
F or personal sa f et y an d proper operation an d mainte-
nan c e o f t h e tool, rea d t h is instru c tion manual be f ore
using t h e tool.
General safety
1 . Any other use except for intended use of
this tool is forbidden. Fastener driving tools
w ith continual contact actuation or contact
actuation shall only be used for production
applications.
Keep ngers away from trigger when not
2.
operating this tool and w hen moving from one
operating position to another.
3. Multiple hazards. Read and understand the
safety instructions before connecting, dis-
connecting, loading, operating, maintaining,
changing accessories on, or w orking near
the tool. Failure to do so can result in serious
bodily injury.
4 . Keep all body parts such as hands and legs
etc. away from ring direction and ensure
fastener cannot penetrate w orkpiece into parts
of the body.
5 . W hen using the tool, be a w are that the fastener
could de ect and cause injury.
Hold the tool with a rm grasp and be prepared
6 .
to manage recoil.
7. Only technically skilled operators should use
the fastener driving tool.
8 . Do not modify the fastener driving tool.
Modi cations may reduce the effectiveness of
safety measures and increase the risks to the
operator and/or bystander.
9 . Do not discard the instruction manual.
1 0. Do not use a tool if the tool has been damaged.
1 1 . Be careful w hen handling fasteners, especially
w hen loading and unloading, as the fasteners
have sharp points w hich could cause injury.
1 2. Al w ays check the tool before use for broken,
misconnected or w orn parts.
1 3. Do not overreach. Only use in a safe w orking
place. Keep proper footing and balance at all
times.
1 4 . Keep bystanders a w ay ( w hen w orking in an area
where there is a likelihood of through traf c of
people ) . Clearly mark off your operating area.
1 5 . Never point the tool at yourself or others.
1 6 . Do not rest your nger on the trigger when
picking up the tool, moving bet w een operating
areas and positions or w alking, as resting
nger on trigger can lead to inadvertent opera-
tion. For tools w ith selective actuation, al w ays
check the tool before use to ascertain the
correct mode is selected.
1 7. Only w ear gloves that provide adequate feel and
safe control of triggers and any adjusting devices.
1 8 . When resting the tool, lay it down on the at sur-
face. If you use the hook equipped w ith the tool,
hook the tool securely on the stable surface.
1 9 . Do not operate when under the in uence of
alcohol, drugs or the like.
Projectile hazards
1 . The fastener driving tool shall be disconnected
w hen unloading fasteners, making adjust-
ments, clearing jams or changing accessories.
2. During operation be careful that fasteners
penetrate material correctly and cannot be
de ected mis red towards operator and or any
bystanders.
3. During operation, debris from w orkpiece and
fastening/collation system may be discharged.
4 . Al w ays w ear protective goggles to protect
your eyes from injury w hen using po w er tools.
The goggles must comply w ith ANSI Z87.1 in
the USA, EN 166 in Europe, or AS/NZS 1336
in Australia/Ne w Zealand. In Australia/Ne w
Zealand, it is legally required to w ear a face
shield to protect your face, too.
6 ENGLISH