Replacing The Power Cable - EINHELL TE-CC 2025 UF Originalbetriebsanleitung

•
Place your hands (with fingers closed) flat on
the workpiece and push the workpiece along
the parallel stop (7) and into the blade (4).
•
Guide at the side with your left or right hand
(depending on the position of the parallel
stop) only as far as the front edge of the gu-
ard hood.
•
Always push the workpiece through to the
end of the splitter (5).
•
The offcut piece remains on the saw table
(1) until the blade (4) is back in its position of
rest.
•
Secure long workpieces against falling off
at the end of the cut (e.g. with a roller stand
etc.).
8.1.2. Cutting narrow workpieces (Fig. 18)
Be sure to use a push stick (3) when making
longitudinal cuts in workpieces smaller than 120
mm in width. A push block is supplied with the
saw! Replace a worn or damaged push stick im-
mediately.
8.1.3.Cutting extremely narrow workpieces
(Fig. 19)
•
Be sure to use a push block when making
longitudinal cuts in very narrow workpieces
with a width of 30 mm and less.
•
The low guide face of the parallel stop is best
used in this case.
•
There is no push block supplied with the
saw! (Available from your specialist dealer).
Replace the push block without delay when it
becomes worn.
8.1.4. Making bevel cuts (Fig. 16/20)
Bevel cuts must always be used using the parallel
stop (7).
•
Set the blade (4) to the desired angle. (See
7.5.)
•
Set the parallel stop (7) in accordance with
the workpiece width and height (see 7.3.1)
•
Carry out the cut in accordance with the work-
piece width (see 8.1.1., 8.1.2 and 8.1.3.)
8.1.5. Making cross cuts (Fig. 21)
•
Slide the cross stop (21) into one of the
grooves (21) in the table and adjust to the
required angle. (See 7.4.) If you also want to
tilt the blade (4), use the groove (21) which
prevents your hand and the cross stop from
making contact with the blade guard.
•
Press the workpiece firmly against the cross
stop (14).
•
Switch on the saw.
Anl_TE_CC_2025_UF_SPK9.indb 29 Anl_TE_CC_2025_UF_SPK9.indb 29
GB
•
Push the cross stop (14) and the workpiece
toward the blade in order to make the cut.
•
Warning!
Always hold the guided part of the workpiece.
Never hold the part which is to be cut off.
•
Push the cross stop (14) forward until the
workpiece is cut all the way through.
•
Switch off the saw again. Do not remove the
offcut until the blade has stopped rotating.
8.1.6 Working with the slide (Fig. 22a, 22b)
8.1.6.1 Releasing the slide
To use the slide (43), open the lever (c).
Secure the cross stop (14) with the screw (20) at
the front end of the slide.
8.1.6.2 Making cuts with the help of the slide
Set the cross stop to the required angle value.
Press the workpiece fi rmly against the stop rail
(14) and push the sliding table slowly toward the
blade.
Push the sliding table forward until the workpiece
is cut all the way through.
Switch off the saw again. Danger! Do not remove
the off cut until the blade has stopped rotating.
8.1.7 Transport (Fig. 23)
The base frame can be fully folded in for transpor-
tation. Alternatively, the base frame can be folded
in on the wheel side and the other side of the
base frame swung right out to enable the machine
to be moved about.

9. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
- 29 -
10.03.2017 07:33:34 10.03.2017 07:33:34