Introduction; Device Description; Scope Of Delivery; Intended Use - Scheppach HL750S Original Bedienungsanleitung

1. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
We hope your new tool brings you much enjoyment
and success.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
We recommend:
Read through the complete text in the operating in-
structions before installing and commissioning the
device.
The operating instructions are intended to help the
user to become familiar with the machine and take
advantage of its application possibilities in accord-
ance with the recommendations.
The operating instructions contain important infor-
mation on how to operate the machine safely, pro-
fessionally and economically, how to avoid danger,
costly repairs, reduce downtimes and how to in-
crease reliability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regu-
lations that apply for the operation of the machine in
your country. Keep the operating instructions pack-
age with the machine at all times and store it in a
plastic cover to protect it from dirt and moisture.
Read the instruction manual each time before oper-
ating the machine and carefully follow its informa-
tion. The machine can only be operated by persons
who were instructed concerning the operation of the
machine and who are informed about the associat-
ed dangers. The minimum age requirement must be
complied with.
20 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
In addition to the safety instructions in this operating
manual and the separate regulations of your country,
the generally recognised technical rules for operat-
ing woodworking machines must also be observed.
We accept no liability for accidents or damage that
occur due to a failure to observe this manual and the
safety instructions.

2. Device description

1. Control handle (hydraulic)
2. Guard
3. Tray table
4. Transport handle
5. Foot
6. Control button (electric motor)
7. Transport wheels

3. Scope of delivery

A. Log splitter
B. Lower cover (large)
C. Lower cover (small)
D. Side cover (large)
E. Side flap
F. Side cover (small)
G. Rear side cover
H. Upper flap
I. Upper cover
J. Corner connection
K. Enclosed accessories bag
a. Hexagon screw M6 x 16 mm + washers (2x)
b. Cylindrical screw M6 x 20 mm + washers and
hexagonal nuts (2x)
c. Safety ring (2x)
d. Wheel cap
e. Cylindrical screw M4 x 12 mm (17x)
f. Hexagon screw M8 x 20 mm (1x)
g. Hexagon nut (M4) (17x)

4. Intended use

The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the manufactur-
er will be liable for any damage or injuries of any kind
caused as a result of this.
To use the equipment properly you must also ob-
serve the safety information, the assembly instruc-
tions and the operating instructions to be found in
this manual. All persons who use and service the
equipment have to be acquainted with this manual
and must be informed about the equipment's poten-
tial hazards. It is also imperative to observe the ac-
cident prevention regulations in force in your area.
The same applies for the general rules of health and
safety at work.