Herunterladen Inhalt Inhalt Diese Seite drucken

Sony GXD-L65H1 Bedienungsanleitung Seite 81

Vorschau ausblenden Andere Handbücher für GXD-L65H1:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 140
"RGB/YUV"
"Display"/"Option": Sets the type of signal for a video device or PC connected
to the HD15 (RGB/COMPONENT) terminal of the display or the 5BNC (RGB/
COMPONENT) terminal of an optional adaptor.
"Auto": Select to choose either an analog RGB input signal or a component
input signal from a connected equipment.
"RGB": Select to choose an analog RGB input signal from a connected
equipment.
"YUV": Select to choose a component input signal from a connected
equipment.
Note
Select "RGB" to input RGB signals using a composite synchronous signal.
Tip
For the available combination of two pictures, see page 28.
"Color System": Select the color system of video signals from "Auto", "NTSC",
"NTSC4.43", "PAL", "PAL-M", "PAL-N" or "PAL60". Select "Auto" to set the
color system automatically.
Note
"Color System" is not available for PC input.
"RGB Signal": When a HD15, DVI or HDMI input terminal 1280 × 768/60 or 720
× 480/60 RGB signal is input, this selects whether it works as a video signal or a PC
signal.
"Screen Saver": This is a setting to prevent or reduce screen burn or after-image
that can occur by long periods of screen display of the same image.
"All White": Displays an all white screen. (Stops automatically after about 30
minutes and the display enters standby mode.)
"Sweep": Scrolls a white bar over the screen.
"Standby": The screensaver operates in standby (page 9) for the time specified
in "Timer Setting." (The display is blank during screensaver operation.) When
the screensaver ends, normal standby mode is resumed.
"Logo": The Sony logo on the front of the unit lights.
"Position": The logo can be constantly lit at the bottom side of the screen by
setting the setup method of the equipment from "Auto," "Landscape," and
"Portrait." If "Auto" is selected, Landscape or Portrait will automatically be
selected.
"Illumination": Select "Off" to have the logo extinguished. Select "Low" and
"High" for the brightness.
"On-Screen Logo"
"On": The model name logo is displayed when the signal is not inputted.
"Off": The model name logo is not displayed when the signal is not inputted.
"Network Port": Sets the network port to operate the display by remote control.
"Off": Select when not using the network port. The power consumption during
standby mode can be reduced.
"Option": Allows you to make settings of the display from a PC connected to
the REMOTE connector or the LAN connector of the OPTION slot. (page 37)
"Display": Allows you to make settings of the display from a PC connected to
the REMOTE (LAN) connector of the display. (page 37)
Tip
When a BKM-FW50 adaptor is inserted in the OPTION slot, "Network Port" is automatically
set to "Option".
"IP Address Setup": Sets an IP address to enable communication speed between
the REMOTE (LAN) connector of the display or the optional adaptor and the
equipment such as a PC connected with the LAN cable.
"Speed Setup": Sets a communication speed between the REMOTE (LAN)
connector of the display or the optional adaptor and the equipment such as a PC
connected with the LAN cable.
Tip
For details on how to make the settings of "IP Address Setup" and "Speed Setup", see the
section of "Preparations for Using the Network Functions" (page 35).
GB
33
GB

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis