Ferm TDM1002 Gebrauchsanweisung Seite 2

1
1
2
Fig.N Fig.T
3
4
1
2
5
1
2
3
Fig.O Fig.U
1
2
Fig.P Fig.V
1
4
5
2
3
Fig.Q Fig.W
1
2
3
Fig.R Fig.X
5
4
3
2
2
1
3
4
Spindle Motor
1 - 469 2 - 946
5
3 - 1576 4 - 2259
5 - 3028
Fig.S Fig.Y
Ferm
2
2
3
RADIAL TABLE DRILL
4
THE NUMBERS IN THE TEXT BELOW
1 CORRESPOND TO THE ILLUSTRATIONS ON
PAGE 2 + 3.
Not included
Caution! For your own safety,carefully read these
instructions for use before using the machine.
Fig.Z
CONTENTS:
1. Technical data
2. Safety instructions
Not included
3. Definitions
4. Directions for assembly
5. Directions for set up
6. Working with the radial table drill
7. Maintenance
1.TECHNICAL DATA
Power
Frequency
Unloaded speed
Number of speeds
Fig.AA
Power drawn
Max.drilling depth
Table rotation
Table dimensions
3 Clearance
2 Dimensions base
Height
1 Spindle distance
3
Chuck opening
1 Lpa (sound pressure level)
2
Lwa (sound power level)
Vibration value
Product information
Fig.A
1 Motor
Fig.BB
2 Mill-cut groove
3 Horizontal toothed rack
4 Rotation locking clamp
5 Table support lock
4
6 Table support
2
7 Conical locking screw
8 Conical scale
9 Vertical locking button
10 Chuck
11 Spring cover
12 Return spring 0
13 On / off switch
3
14 Base
1
15 Stand
16 Table
17 Drilling grips
18 Depth scale locking knob
19 Depth scale indicator
20 Protractor
21 Horizontal drill button
22 V-groove
23 Belt tension locking button
24 Tilt locking clamp
25 Mill-cut groove
26 Drive belt guard
3
27 Spindle pulley block
28 Motor pulley block
1
2
General guidelines
• Inspect all parts after unpacking,for possible damage
during transport.In the event of transport damage,
the carrier should be immediately notified.
• Complaints made later will not be accepted.
• Inspect the delivery for completeness.
• Become familiar with the machine by reading the
operator's guide thoroughly prior to first use.
• When fitting/replacing accessories,wear- and
reserve parts,use exclusively original Ferm parts.
Spare parts are available from your supplier.
• When ordering,please specify our article number
and the machine type.
Remark:According to the applicable product liability
law,the manufacturer of this appliance is not liable for
damage caused to or by this appliance,arising from:
• Negligent operation.
• Failure to follow the instructions in the operator's
guide.
3 4
• Repairs carried out by third parties,and unqualified
workmen. Only insert the plug in the wall socket,once you
• The fitting of,or replacement with,other than have read and understood the following directions,
original Ferm spare parts. to avoid faults that could cause injury.
• Usage other than that for which the machine is
designed,failure of the electrical installation,by not 1. Read the entire operator's guide and become
observing the electrical regulations and the VDE familiar with its contents.Learn how you should use
provisions 0100,DIN 57113 1 VDE 0113. the tools and what the limitations and potential
hazards are.
We strongly recommend: 2. Be absolutely certain that all safety precautions are
operational,and that they are in a good state.
Before assembling and using the machine,read 3. Remove adjustment tools and spanners.Get
the complete text of the operator's guide. accustomed to checking,before switching on the
machine,whether adjustment tools and spanners
This operator's guide is designed to make it easier for have been removed.
you to get to know your machine,and to learn how to 4. Keep the work surface clean.Untidy and fouled work
make use of it's many functions. surfaces cause accidents.
The operator's guide includes important directions as 5. Never use the machine in an unsafe environment.
to how you can safely,expertly and economically employ Never use electrical equipment in damp or wet
the machine,and how you can avert hazards,save on places,and protect them from rainwater.Ensure
repair costs,reduce unavailability,and increase the good lighting of the work area.
reliability and useful life of the machine. 6. Keep children at a distance.Persons,who are not
working with the machine,should maintain a safe
Besides following the safety guidelines in this operator's distance from the work area.
guide,you should give your fullest attention to the 7. Use locks if necessary,to ensure that children cannot
regulations applicable in your country for the use of this enter the work area.
machine. 8. Never apply brute force on or about the machine.
| 230 V
The machine functions better and more safely at the
| 50 Hz
Keep the operator's guide close to the machine,packed speed it was designed for.
| 469-3028/min
inside a plastic sleeve to protect it from dirt and 9. Use appropriate tools.Do not try to use force to apply
| 5
moisture.It should be carefully read and strictly followed the machine to operations it was not designed for.
| 350 W
by every operator of the machine.Only persons who 10. Use a regulation extension cable certain that it is in a
| 100 mm
have received instruction in the operation of the good state.The extension cable must be strong
| 0˚ to 45˚ (L/R)
machine and who are aware of the potential hazards enough to carry the current drawn by the tool for
| 220 x 195 mm
should be allowed to operate the machine.The your workpiece.A cable that is too weak will
| 115 x 435 mm
minimum age should be heeded. dissipate the current,which leads to power loss and
| 345 x 225 mm
overheating.
| 725 mm
Besides the safety guidelines in this operator's guide and 11. Work with the right equipment.Do not wear loose
| 100 - 340 mm
the specific regulations applicable in your country,the clothes,gloves,ties,rings,armbands or other
| 13 mm
generally recognised technical rules for the use of accessories that could come in contact with moving
| 65.5 dB(A)
woodworking machines should also be heeded. parts.Wear anti-slip shoes.Protect long hair by using
| 78.5 dB(A)
a hairnet.
| 0.853 m/s 2
Unpack the contents of the box and inspect them 12. Wear safety glasses.Your eyes are your most valuable
closely. possession.Always wear safety glasses.Every drill can
throw foreign objects into the eyes,which can cause
Should any part be missing or damaged,do not irreparable harm.Always wear safety glasses that
connect the machine to the power supply until the conform to the safety guidelines (not a normal pair
machine is complete and in order. of glasses.) Normal optical glasses offer no
protection against objects flying around.They have
Unpack the machine and parts carefully,and compare no safety glass in the lenses.If these lenses break,this
them to the drawing. can cause serious injury.
To protect the drill from moisture,the surfaces have 13. Wear a face- or dust mask.Drills create dust.
been coated with a protective layer which you can 14. Work safely.Make as much use as possible of a clamp
remove using a soft cloth and WD-40. or vice.This is safer than using your hands,and leaves
both hands free to operate the machine.
To prevent danger of fire or poisonous fumes,never 15. Remove the plug from the power socket when
use petrol,naphtha,acetone,thinners or similar performing maintenance,and when changing
volatile solutions for cleaning the machine. accessories such as cutter,drill,routing bit,etc.
16. Reduce the risk of unintended activation of power.
Verify that the power switch is OFF,before you
2.SAFETY INSTRUCTIONS
connect mains power.
17. Only use recommended accessories.These
In this operator's guide the following pictograms are
accessories can be found in the operator's guide.
used:
Poorly fitting accessories create a substantial risk of
personal injury.
CE Conforms to the applicable European safety
18. Never stand on the machine.This can cause serious
standards
injury,should the machine tilt,or if you accidentally
come into contact with the cutting tools.
Danger of bodily injury or material damage.
19. Inspect the machine for damaged parts.Before you
make further use of the machine,any damaged safety
features as well as any other damaged part must be
Indicates electrical shock hazard.
carefully inspected,as to whether they still function
without problem and can still perform their specific
task.Inspect all moving parts for alignment,position,
Read the instructions
and correct couplings;furthermore check for
breakages,correct assembly and any other
conditions that could have an influence on the
Keep bystanders at a distance
machine's functioning.Any damaged safety features
or damaged part must be repaired or replaced in a
workmanlike way.
Immediately unplug the plug from the mains
20. Never leave a running machine unattended.First
electricity in the case that the cord gets damaged
turn off the power.Only leave the machine once it
and during maintenance
has completely stopped moving.
21. Do not excessively lean,either forwards or
Wear eye and ear protectors
sideways.Always ensure you have a stable footing,
and keep your balance.
22. Perform maintenance on the machine with care.For
Faulty and/or discarded electrical or electronic
correct and safe operation,the tools must be sharp
apparatus have to be collected at the appropriate
and clean.Follow carefully the directions for honing
recycling locations.
and replacement of tools.
23. Never use electrical machines in the presence of
General safety instructions
inflammable fluids or gases.
24. Do not work with the machine if you are under the
Safety is a combination of common sense,continual
influence of drugs,alcohol or medicines that could
alertness and a good knowledge of the machine's
limit your capability to react.
operations.
EXPLODED VIEW
Ferm
Ferm
53