Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Changing the beam angle
For a softer light with varying beam angles, please use the enclosed Diffuser Cover Kits.
With the delivery of the device you receive two Diffuser Cover Kits, with which the beam angle can be
changed from 9 ° to 42 °. If you want to change the beam angle of the spots, attach the desired diffuser
cover to the front of each spot using the two knurled screws. Make sure the screws are tightened to prevent
accidental release of the diffuser cover.
Attaching further light effects
The light set offers mounting points for attaching further lighting effect units (e.g. spot lights, flower effects or
lasers). For this loosen the fixation screw on the upper side, attach the light effect through its bracket and
tighten the fixation screw.
CONNECTIONS
Device 3
Starting address 33
MIC
LED KLS-190 Compact Light Set
LED
No. 42109608, EAN 4026397657715
100-240V~ 50/60Hz 60W
T1A/250V
0.1m
T =45°C
T =55°C
a
KLS-190
c
Steinigke Showtechnic GmbH Andreas-Bauer-Str. 5
97297 Waldbüttelbrunn Germany www.steinigke.de
MENU
UP DOWN ENTER
Compact Light Set
120 Ohms
DMX512 control
A DMX512 data link is required in order to control the device via DMX. The device provides 3-pin XLR
connectors for DMX connection.
1
Connect the output of your DMX controller to the DMX input DMX IN of the light set with a DMX cable.
2
Connect the DMX output DMX OUT of the light set to the DMX input of the next unit in the chain. Always
connect one output to the input of the next unit until all units are connected.
3
At the last unit, the DMX cable has to be terminated. Plug the terminator with a 120 Ω resistor between
Signal (–) and Signal (+) in the DMX output of the last unit.
4
If the cable length exceeds 300 m or the number of DMX devices is greater than 32, it is recommended
to insert a DMX level amplifier to ensure proper data transmission.
XLR connection:
Device 2
Starting address 17
FUSE:
MIC
T1A, 250 V
LED KLS-190 Compact Light Set
LED
No. 42109608, EAN 4026397657715
SAFETY ROPE
100-240V~ 50/60Hz 60W
T1A/250V
0.1m
T =55°C
T =45°C
a
KLS-190
c
Steinigke Showtechnic GmbH Andreas-Bauer-Str. 5
97297 Waldbüttelbrunn Germany www.steinigke.de
MENU
UP DOWN ENTER
Compact Light Set
P
OWER SUPPLY
:
100- 4
2 0 V ~ 50
/60
Hz
Starting address 1
FUSE:
MIC
T1A, 250 V
LED KLS-190 Compact Light Set
LED
No. 42109608, EAN 4026397657715
SAFETY ROPE
100-240V~ 50/60Hz 60W
T1A/250V
0.1m
a
T =45°C
T =55°C
KLS-190
c
Steinigke Showtechnic GmbH Andreas-Bauer-Str. 5
97297 Waldbüttelbrunn Germany www.steinigke.de
MENU
UP DOWN ENTER
Compact Light Set
P
OWER SUPPLY
:
100- 4
2 0 V ~ 50
/60
Hz
30/44
Device 1
FUSE:
T1A, 250 V
SAFETY ROPE
P
OWER SUPPLY
:
100- 4
2 0 V ~ 50
/60
Hz
DMX-512 Controller
00122636.DOCX, Version 1.0
Werbung
Inhaltsverzeichnis
