Technical Data - Scheppach 5911902903 Originalbetriebsanleitung

16. Prior to use. always perform a visual inspection to
check whether the work tools and bolts are worn
out or damaged. To prevent an imbalance, worn
out or damaged work tools and bolts may only be
replaced in sets. Only work with the machine in
daylight or with good artificial lighting.
17. If possible, avoid using the device on wet grass
or take special care to prevent slipping.
18. Only guide the machine at walking pace.
19. Always work across a slope, never upwards or
downwards.
20. Take particular care when changing direction on
a slope.
21. Do not work on excessively steep slopes.
22. Take particular care when reversing the machine
or pulling it towards you.
23. Never use the machine with damaged or miss-
ing safety guards, e.g. without deflectors and/or
catcher.
24. Disconnect all work tools and drives before start-
ing the engine.
25. Start or press the starter switch with caution in
accordance with the manufacturer's instructions.
Ensure that your feet are far enough away from
the work tool(s).
26. When starting the engine, do not tilt the machine
unless it has to be lifted during the process. In
this case, only tilt as far as absolutely required
and only lift the side away from the operator.
27. Do not start the engine if you are standing in front
of the ejector chute.
28. Close the throttle valve when running down the
engine; if the engine is equipped with a petrol
shut-off valve, close this after aerating the soil
or scarifying
29. Switch the engine off by removing the spark plug
connector and the ignition key on machines with
a battery starter:
• if you leave the machine
• before refuelling
30. Switch the engine off by removing the spark plug
connector and the ignition key on machines with
a battery starter:
• before releasing blockages or rectifying ob-
structions in the discharge duct,
• before checking or cleaning the machine, or
performing work on it,
• if it came into contact with a foreign object.
Inspect the machine for damage and perform
the required repairs before starting again and
working with the machine,
• if the machine starts to vibrate unusually
strongly (inspect immediately)
Instructions for maintenance
Before cleaning, repair, inspecting, or adjusting, shut
off the engine and make certain all moving parts have
stopped. Disconnect the spark plug wire, and keep
the wire away from the plug to prevent accidental
starting.
22 GB
Have your machine serviced by qualified repair per-
sonnel using only identical replacement parts. This
will ensure that the safety of the machine maintained.

6. Technical data

Engine type
Displaycement
Max. engine output
Working speed
Fuel
Tank capacity
Engine oil
Tank capacity /oil
spark plug
Depth setting
Working width
Number of blades
Blade diameter
Collection bag capacity
Weight
Subject to technical changes!
Information concerning noise emission measured
according to relevant standards:
Sound pressure LpA = 85,9 dB(A)
Sound power LWA = 101,2 dB(A)
Uncertainty KPA = 3,43 dB(A)
Wear ear-muffs. The impact of noise can cause
damage to hearing.
Vibrations:
Vibration Ahv (left/right) = 7,03 m/s²
Uncertainty KPA = 1.5 m/s
Keep the noise emissions and vibrations to a
minimum.
• Only use appliances which are in perfect work-
ing order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
Before starting the equipment
Before you connect the equipment to the mains sup-
ply make sure that the data on the rating plate are
identical to the mains data.
1-cylinder; 4 - stroke
212 cm³
4,0 kw
3400 rpm
unleaded fuel
3,6 l
10W 30 / SAE 30
0.6 L
F7TC
+5 / -15
400 mm
18
165 mm
45L
38 kg