How To Use The Accessories; Care And Service - Kärcher WD 2 Plus Bedienungsanleitung

ATTENTION
Operation with full container
When the container is full, a float switch closes the suc-
tion opening and the device runs at a higher speed.
Switch off the device immediately and empty the con-
tainer.
Note
If the device falls over, the float can also close. To make
the device capable of vacuuming again, set up the de-
vice, switch it off, wait 5 seconds and then switch it on
again.
Working with power tools (only for devices
with a built-in socket)
CAUTION
Unintentional starting of the power tool
Injury or property damage
Make sure that the power tool is ready for operation as
soon as it is connected to the device socket.
1. Connect the suction hose.
Illustration F
2. If necessary, the adapter can be adjusted to the con-
nection diameter of the power tool with a suitable
tool.
3. Option A) Put the adapter on the handle of the suc-
tion hose. Connect the suction hose to the adapter
on the power tool.
Option B) For more flexibility when working, connect
the adapter to the thin tool hose and the handle of
the suction hose and connect it to the power tool.
Option C) With some power tools, the handle of the
suction hose can be connected directly to the power
tool.
Illustration N
4. Plug the mains plug of the power tool into the device
socket.
Illustration O
5. Set the trigger to MAX
The power can be regulated using the rotary switch.
The suction is activated automatically.
Illustration M
Note
Note the maximum connected load (see information on
the device socket).
Note
As soon as the power tool is switched on, the suction
turbine starts up with a 0.5 second delay. If the power
tool is switched off, the suction turbine continues to run
for approx. 5 seconds in order to suck in the residual dirt
in the suction hose.
Blower function
The blower function can be used to clean areas that are
difficult to reach or where vacuuming is not possible,
e.g. leaves in a gravel bed.
 Insert the suction hose into the blower connection.
The blower function is now activated.
Illustration P
Interrupting operation
1. Set the trigger to "0 OFF".
The device is switched off.
2. Variant 1: Place the handle of the suction hose in the
intermediate parking position.
Illustration Q
Variant 2: Attach the floor nozzle in the parking po-
sition.
Illustration R
10
1. Set the trigger to "0 OFF".
The device is switched off.
2. Pull out the mains plug.
3. Remove the device head.
Illustration B
4. Empty the container.
Illustration S
5. Storage possibility:
Illustration V
Note
The suction hose can be wrapped around the device
head and attached to the device head with the help of
the hose collar.
6. Store the device in a dry and frost-proof room.

How to use the Accessories

General instructions for use
 Connect the floor nozzle to the suction pipes.
Illustration I
 Connect the various nozzles, such as the crevice
nozzle, to the handle or attach it directly to the suc-
tion hose.
Switchable floor nozzle
Note
Only use the floor nozzle to vacuum dry dirt.
● For vacuuming carpet, use the position with brush
strips retracted on the bottom.
● For vacuuming hard floors, use the position with the
brush strips extended on the bottom.
Illustration J
Upholstery nozzle
● For vacuuming upholstered furniture, mattresses,
curtains, etc.
● For quickly cleaning larger textile surfaces in the car,
such as the boot, foot room, back seat.
Extra long crevice nozzle
● For cleaning hard-to-reach places, such as between
the car seats.
Suction brush with hard bristles
● For thoroughly cleaning upholstery and carpet in the
car.
Suction brush with soft bristles
● For gently cleaning sensitive surfaces in the car
such as the dashboard or centre console.
or
● For gently cleaning sensitive surfaces or delicate
items such as those on the workbench.

Care and service

General care instructions
 Clean the device and plastic accessory parts with a
commonly available plastic cleaner.
 Rinse the container and accessories with water, as
necessary, and dry them before further use.
Clean the foam filter / cartridge filter
1. If necessary, the foam filter / cartridge filter can be
cleaned under running water. To do this, remove the
foam filter from the filter basket. The cartridge filter
English
Ending operation
Car nozzle