Initial Start-Up; Dry Vacuuming - Kärcher WD 2 Plus Bedienungsanleitung

Suction hose (WD 2 Plus / KWD 2)
19
Removable handle (WD 3 / KWD 3)
20
Suction hose with connection piece (WD 3 / KWD 3)
21
Suction pipes 2 x 0.5 m
22
Crevice nozzle
23
** Floor nozzle with insert for wet and dry vacuuming
24
Adapter for connecting power tools
25
Switchable floor nozzle for carpets and hard floors
26
(home)
Upholstery nozzle (home)
27
2x filter bags (home)
28
Car nozzle (car)
29
Extra long crevice nozzle (car)
30
Suction brush with hard bristles (car)
31
Suction brush with soft bristles (car / workshop)
32
Flexible tool hose (workshop)
33
** Not included with the home version
Installing the steering rollers
1. Before initial startup, remove contents from the con-
tainer.
Illustration B
Illustration C
Note
For devices with stainless steel containers, the acces-
sories are not in the container, they are outside of it.
Initial startup
ATTENTION
Vacuuming without a foam or cartridge filter
Device damage
Always ensure that the foam or cartridge filter is insert-
ed, for both wet vacuuming and dry vacuuming.
Inserting the filter bag
1. Fully unfold the filter bag.
2. Attach the filter bag to the device connection and
press it on firmly.
Illustration D
3. Fit and lock the device head.
Illustration E
Note
We recommend using a filter bag to vacuum fine dust.
Installing the hose, pipes, floor nozzle
1. Connect the suction hose.
Illustration F
2. Connect the suction hose to the handle.
Illustration G
Note
For convenient vacuuming in confined spaces, the han-
dle can be removed, and the accessories plugged di-
rectly onto the suction hose.
To release the handle, the grey areas on both sides of
the handle must be pressed, and the handle pulled from
the hose.
3. Install the floor nozzle.
 Install the insert in the floor nozzle.
 Connect the floor nozzle to the suction pipes.
Illustration H
Starting up the device
1. Plug the mains plug into the socket.
Illustration K
Devices without a socket
2. Set the trigger into the desired position.
Illustration L
 Position "1 ON": The suction / blower function is
activated.
 Position "0 OFF": The device is switched off.
Devices with a socket
3. Set the trigger into the desired position.
Illustration M
 Position "1 ON": The suction / blower function is
activated.
 Position
the suction is activated automatically.
 Position "0 OFF": The device is switched off.
Note
As long as the device is supplied with power, the device
socket can be used as a power source.
Note
Limited for Switzerland only: The socket outlet shall on-
ly be used during operation in dry condition.
Note
Pay attention to the latest part numbers when purchas-
ing and installing filter bags and cartridge filters.
Information on accessories and spare parts can be
found at www.kaercher.com.
ATTENTION
Vacuuming cold ashes
Device damage
Only vacuum cold ash with an ash pre-separator.
ATTENTION
Defective or wet foam filter / cartridge filter
Device damage
Before starting up, check the foam filter / cartridge filter
for damage, and replace it if necessary. Only vacuum
with a dry foam filter / cartridge filter.
Depending on the equipment variant, a foam filter or a
cartridge filter is included.
 For devices with a foam filter: Always use the filter
bag in addition to the foam filter when dry vacuum-
ing.
 For devices with a cartridge filter: Always use the fil-
ter bag in addition to the cartridge filter when vacu-
uming fine dust.
Note
Replace the filter bag in good time, as a filter bag that is
too full could be damaged. The fill degree of the filter
bag depends on the amount of dirt vacuumed. The filter
bag should be replaced more frequently when vacuum-
ing fine dust, sand, etc.
ATTENTION
Wet vacuuming with a filter bag
Device damage
Do not use a filter bag when vacuuming wet.
English
: When the power tool is connected,
Operation

Dry vacuuming

Wet vacuuming
9