Drilling Operation; Optional Accessories - Makita DA3010 Betriebsanleitung

Installing side grip (auxiliary handle)
CAUTION:
Always be sure that the side grip is
installed securely before operation.
Screw the side grip on the tool securely. The side grip
can be installed on either side of the tool, whichever is
convenient.
► Fig.4: 1. Side grip
Installing or removing drill bit
CAUTION:
Always be sure that the tool is
switched off and unplugged before installing or
removing the drill bit.
For model DA3010, DA3010F
► Fig.5: 1. Drill chuck 2. Chuck key
To install the drill bit, place it in the drill chuck as far as
it will go. Tighten the chuck by hand. Place the chuck
key in each of the three holes and tighten clockwise. Be
sure to tighten all three chuck holes evenly.
To remove the drill bit, turn the drill chuck key counter-
clockwise in just one hole, then loosen the chuck by
hand.
After using the chuck key, be sure to return it to the
original position.
For model DA3011, DA3011F
► Fig.6: 1. Sleeve 2. Ring
Hold the ring and turn the sleeve counterclockwise to
open the chuck jaws. Place the drill bit in the drill chuck
as far as it will go. Hold the ring firmly and turn the
sleeve clockwise to tighten the chuck.
To remove the drill bit, hold the ring and turn the sleeve
counterclockwise.
OPERATION
Holding the tool
CAUTION:
Hold the tool firmly with one hand
on the gripping part of the tool and the other hand
on the side grip when performing the tool.
► Fig.7

Drilling operation

Drilling in wood
When drilling in wood, the best results are obtained
with wood drills equipped with a guide screw. The guide
screw makes drilling easier by pulling the drill bit into
the workpiece.
Drilling in metal
To prevent the drill bit from slipping when starting a
hole, make an indentation with a center-punch and
hammer at the point to be drilled. Place the point of the
drill bit in the indentation and start drilling.
Use a cutting lubricant when drilling metals. The excep-
tions are iron and brass which should be drilled dry.
CAUTION:
Pressing excessively on the tool will
not speed up the drilling. In fact, this excessive pressure
will only serve to damage the tip of your drill bit, decrease
the tool performance and shorten the service life of the tool.
CAUTION:
Hold the tool firmly and exert care
when the drill bit begins to break through the
workpiece. There is a tremendous force exerted on
the tool/drill bit at the time of hole break through.
CAUTION:
A stuck drill bit can be removed
simply by setting the reversing switch to reverse
rotation in order to back out. However, the tool
may back out abruptly if you do not hold it firmly.
CAUTION:
Always secure workpieces in a
vise or similar hold-down device.
CAUTION:
Avoid drilling in material that you
suspect contains hidden nails or other things that
may cause the drill bit to bind or break.
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and unplugged before attempting to
perform inspection or maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY, repairs, carbon
brush inspection and replacement, any other maintenance or
adjustment should be performed by Makita Authorized or Factory
Service Centers, always using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
These accessories or attachments are
recommended for use with your Makita tool specified in
this manual. The use of any other accessories or attach-
ments might present a risk of injury to persons. Only use
accessory or attachment for its stated purpose.
If you need any assistance for more details regarding these
accessories, ask your local Makita Service Center.
• Drill bits
• Chuck key
• Grip 36
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
5 ENGLISH