Compound Cutting; In The Case Of Left Bevel Cut - Makita DLS714 Betriebsanleitung

CAUTION:
(Only for tools with sub-fence)
Always set the sub-fence outside when perform-
ing left bevel cuts.
► Fig.47: 1. Holder assembly
1. Loosen the lever and tilt the saw blade to set the
bevel angle (Refer to the previously covered "Adjusting
the bevel angle"). Be sure to retighten the lever firmly to
secure the selected bevel angle safely.
2.
Secure the workpiece with a vise.
3.
Pull the carriage toward you fully.
4. Switch on the tool without the blade making any
contact and wait until the blade attains full speed.
5. Gently lower the handle to the fully lowered posi-
tion while applying pressure in parallel with the blade
and push the carriage toward the guide fence to cut
the workpiece.
6.
When the cut is completed, switch off the tool and
wait until the blade has come to a complete stop
before returning the blade to its fully elevated position.
NOTICE:
When pressing down the handle, apply
pressure in parallel with the blade. If a force is
applied perpendicularly to the turn base or if the pres-
sure direction is changed during a cut, the precision
of the cut will be impaired.

Compound cutting

Compound cutting is the process in which a bevel
angle is made at the same time in which a miter angle
is being cut on a workpiece. Compound cutting can be
performed at the angle shown in the table.
Miter angle
Left and Right 45°
Right 50°
Right 55°
Right 57°
When performing compound cutting, refer to "Press
cutting", "Slide cutting", "Miter cutting" and "Bevel cut"
explanations.
Cutting crown and cove moldings
Crown and cove moldings can be cut on a compound
miter saw with the moldings laid flat on the turn base.
There are two common types of crown moldings and
one type of cove moldings; 52/38° wall angle crown
molding, 45° wall angle crown molding and 45° wall
angle cove molding.
► Fig.48: 1. 52/38° type crown molding 2. 45° type
crown molding 3. 45° type cove molding
Bevel angle
Left 0° - 45°
Left 0° - 40°
Left 0° - 30°
Left 0° - 25°
23 ENGLISH
There are crown and cove molding joints which are
made to fit "Inside" 90° corners ((a) and (b) in the figure)
and "Outside" 90° corners ((c) and (d) in the figure.)
(a) (b)
1. Inside corner 2. Outside corner
► Fig.49: 1. Inside corner 2. Outside corner
Measuring
Measure the wall width, and adjust the width of the
workpiece according to it. Always make sure that width
of the workpiece's wall contact edge is the same as wall
length.
► Fig.50: 1. Workpiece 2. Wall width 3. Width of the
workpiece 4. Wall contact edge
Always use several pieces for test cuts to check the saw angles.
When cutting crown and cove moldings, set the bevel
angle and miter angle as indicated in the table (A) and
position the moldings on the top surface of the saw
base as indicated in the table (B).

In the case of left bevel cut

(a) (b)
1. Inside corner 2. Outside corner
Table (A)
– Molding Bevel angle
position
52/38°
in the
type
figure
For (a) Left
inside 33.9°
corner
(b)
For (c)
outside
(d)
corner
(c) (d)
1 2
(c) (d)
1 2
Miter angle
45° type 52/38°
type
Left 30° Right
31.6°
Left
31.6°
Right
31.6°
45° type
Right
35.3°
Left
35.3°
Right
35.3°