Thank you for purchasing the Nikon Lite Touch Zoom 70W / Lite Touch Zoom 70W QD camera. Be sure to read this manual thoroughly before use, and keep it handy until you feel confident using the camera. Your Nikon camera features: •...
Shooting a distant view or landscape through a window _____________ 28 Using the self-timer _____________________________________ 28 Close-up photography ___________________________________ 29 Imprinting the date/time on pictures (Lite Touch Zoom 70W QD only) _______________________ 30 Additional Information Correcting the date and time (Lite Touch Zoom 70W QD only) _______________________ 31...
Camera parts (Body) Macro button Auto Exposure p. 29) metering window Red-eye Reduciton lamp ( p. 26, 27) Self-Timer lamp Lens p. 28) Viewfinder window p. 7) Autofocus window Autofocus window Slide cover (power switch) p. 9) Flash ( pp. 20-27) LCD panel ( p.
Seite 5
(for correcting data) Tripod socket p. 31) SEL button* (for selecting the position MODE button* of data to be corrected) (for selecting data to be p. 31) imprinted or corrected) pp. 30, 31) * Lite Touch Zoom 70W QD only Getting Started...
LCD panel Self-Timer indicator p. 28) Infinity Focus Mode indicator p. 28) Frame counter ( p. 11) Low battery power indicator p. 9) Red-eye Reduction indicator pp. 26, 27) Flash Mode indicator pp. 20-25) The illustrations are fully labeled for your reference. Getting Started...
Indications in the viewfinder 1Parallax compensation marks For shooting in Macro mode at a distance of approx. 0.6 m (2.0 ft.). 2Autofocus frame marks ( p. 15) Center the main subject to be in focus within this frame. 3Red LED Momentarily lights: Focus is achieved.
Installing a battery Battery type Use one CR2 3V lithium battery in this camera. Open the battery chamber lid. Open the battery chamber lid to the direction indicated by the arrow in the illustration. Install a new battery. Observe the correct polarities and insert the battery in the direction shown in the illustration above.
Turning the camera on Open the slide cover. Once you open the cover in the direction of the arrow, the camera is turned on, the built-in flash pops up, and the lens protrudes. If the camera is not operated for more than 3 minutes, the lens automatically retracts to the (wide-angle) position.
Loading the film Tips on 35mm film Number of frames DX code DX mark DX-coded 35mm film Film cartridge Film speed Use DX-coded 35mm film with this camera. For DX-coded film, film speed is automatically set. Film speeds valid for automatic setting are ISO100 and 400. (When using ISO200 film or non-DX film, the film speed is automatically set to ISO100.) When loading/unloading film, be sure not to open the camera...
Seite 11
Pull the film leader out to the red index mark. Hold the film cartridge and ensure film is properly positioned with no slack. Close the camera back, and check that the film has been correctly loaded. When the film has been properly set, “ ” is displayed on the frame counter when the camera is turned on.
Nikon cannot be held responsible for malfunctions caused by using the Lite Touch Zoom 70W / Lite Touch Zoom 70W QD in ways not specified in this manual. Basic Operations...
Operating the Shutter Release button Lightly press the button and confirm the red LED lights up. When you press the button lightly, the focus and exposure are achieved, and the red LED lights up. The focus is locked (Focus lock p.
Zooming Press the Zoom lever to compose the picture. Press the lever to the direction of for telephoto (70mm) photography or to the direction of for wide-angle (28mm) photography. Remove your finger from the lever when the desired image size is obtained. If the camera is not operated for more than 3 minutes, the lens automatically retracts to the (wide-angle) position.
Shooting Center the autofocus frame mark on the main subject. If the main subject is outside the autofocus frame: If the main subject is outside the autofocus frame, use the focus lock to achieve focus. ( p. 18) Lightly press the Shutter Release button. The relationships between the red LED indications and the camera functions are shown in the table below: Focusing...
Seite 16
Shooting (continued) *1 While the red LED is blinking with the Shutter Release button pressed lightly, the flash is being charged, and the shutter cannot be released. Lightly press the Shutter Release button again, and release the shutter after the red LED stops blinking and stays lit.
Rewinding the film Film rewinds automatically. At the end of the film roll, the film rewinding starts automatically. While the film is rewinding, the number on the frame counter decreases one by one. When rewinding is complete, “ ” blinks, then stops blinking and remains lit. If rewinding stops midway through the roll because of a dead battery, it resumes automatically as soon as the battery is replaced.
When the main subject is not in the center of the picture Focus lock photography When the subject to be focused is outside the autofocus frame in the center of the picture, use focus lock, which enables you to change the picture composition while locking the focus.
Difficult-to-focus subjects The following subjects may be difficult to focus. Use the focus lock ( p. 18) to focus on another subject equidistant from the camera, then compose the picture to shoot. Subjects too small to fully cover the autofocus frame mark.
Flash photography Selecting the flash mode You can select any of five flash modes by pressing button. : Auto Flash( p. 22) The flash automatically fires when there is not enough light. : Infinity Focus( p. 28) For shooting a distant scene or landscape more sharply.
Procedure for Flash Photography Press the button to select the Flash mode. Since slow shutter speeds are usually selected in (Flash Cancel) and (Slow Sync Flash) modes, use a tripod to prevent camera shake. Compose the picture, then lightly press the Shutter Release button.
To automatically fire the flash Auto Flash mode The flash automatically fires when the subject is dark. Make sure that the “ ” mark appears on the LCD panel. If the “ ” mark does not appear, press the button until “...
To cancel flash operation Flash Cancel mode Use this mode in places, such as museums, where flash photography is prohibited. Use a tripod or place the camera on a stable flat surface. Use a tripod for Flash Cancel mode Since slow shutter speeds are usually selected in this mode, use a tripod to prevent camera shake.
To fire the flash intentionally Anytime Flash mode Use this mode to intentionally fire the flash without regard to light conditions. Press the button until “ ” appears on the LCD panel. Make sure that the red LED lights up, then shoot.
To photograph a person in a night view Slow Sync Flash mode Use this mode to brighten both the subject and the background in a night view or at dusk. Use a tripod or place the camera on a stable flat surface. Use a tripod for Slow Sync Flash mode Since slow shutter speeds are usually selected in this mode, use a tripod to prevent camera shake.
To reduce the "Red-eye" effect Red-eye Reduction mode In flash photography, the subject’s eyes may sometimes appear bright red. To reduce this “red-eye” effect, use this mode. Press the button until “ ” appears on the LCD panel. Each time you press the button, the indicator changes in the order shown below: No indicator...
Seite 27
Compose the picture, then lightly press the Shutter Release button. Check that the red LED lights up, then shoot. Both camera and subject be still The Red-eye Reduction lamp lights up for approx. a second before the flash fires. Be careful not to move the camera or let the subject move until the flash fires.
Shooting a distant view or landscape through a window Infinity Focus mode This mode is good for shooting a distant view more sharply, or a landscape through a window. Press the button until “ ” appears on the LCD panel. Check that the red LED momentarily lights, then shoot.
Close-up photography Minimum camera-to-subject distance is apporox. 0.6 m (2.0 ft.) in Telephoto shooting If you wish to shoot a subject such as a flower as large as possible, you can get as close to the subject as apporox. 0.6 m (2.0 ft.).
Imprinting the date/time on pictures (Lite Touch Zoom 70W QD only) Select the date/time indicator by pressing the MODE button. The year is indicated by the lower two digits (“ ” for 2000 and “ ” for 2001) and printed, and the time is in the 24-hour cycle.
Correcting the date and time (Lite Touch Zoom 70W QD only) Press the MODE button to obtain the Year/Month/Day indication. Press the SEL button so that the indicator to be set blinks. Press the ADJUST button to set the blinking digit.
Replacing the battery for date (Lite Touch Zoom 70W QD only) If the date/time printed on film is dark or difficult to read, the battery for date must be exhausted. Replace it with a new one. Battery type Use one CR2025 3V lithium battery for date with this camera.
Seite 33
Replace the battery with a new one. Install the new battery with the polarity upward as illustrated. Close the date battery chamber lid and tighten the screws. Firmly tighten the screws using a screwdriver. The built-in clock is reset when the battery is removed. Remember to set the time and date.
Troubleshooting Track down the cause of trouble using the following chart. It may save you a trip to your nearest Nikon service center. Problem Check points and solution Ref. page a The battery is installed with wrong The shutter polarities.
Seite 35
Problem Check points and solution Ref. page The numeral a “ ” appears on the LCD panel when the camera is turned on by opening the slide “ ” does not appear even cover. when film is Remove the film and load it again. 10,11 loaded.
Keep the camera dry: The Lite Touch Zoom 70W / Lite Touch Zoom 70W QD is not waterproof, and therefore should not be exposed to rain or saltwater. Do not apply strong shock to the camera: Do not drop the camera or hit it against a hard surface.
Specifications Type of camera 35mm autofocus lens-shutter camera with Nikon zoom lens Usable film DX-coded 35mm film in film cartridge Picture format 24 × 36 mm Lens 28 mm f/5.6–70 mm f/10, 5 elements in 4 groups Shutter Programmed electronic type Viewfinder Real-image viewfinder;...
Seite 38
Approx. 117 × 63 × 42 mm (4.6 × 2.5 × 1.7 in) Lite Touch Zoom 70W Lite Touch Zoom 70W QD Approx. 117 × 63 × 47 mm (4.6 × 2.5 × 1.9 in) Weight (without battery) Lite Touch Zoom 70W Approx.
Remove the battery and take the camera to your nearest Nikon dealer for repair. • If you detect smoke coming from the camera, stop operation immediately and turn the camera off.
Seite 40
For safe handling of the camera (continued) CAUTION • Do not fire the flash close to a person’s eyes, as this may cause blindness. In particular, keep a distance of at least 1m when taking a pictures of children. • Do not touch the camera with wet hands, as this may cause electric shock.
Danke, daß Sie sich für die Kamera Lite Touch Zoom 70W/ Lite Touch Zoom 70W QD von Nikon entschieden haben. Bitte lesen Sie diese Anleitung sorgfältig durch, bevor Sie die Kamera benutzen, und halten Sie die Anleitung griffbereit, bis Sie mit der Kamera vertraut sind.
Seite 43
Fenster ___________________________________________ 68 Der Selbstauslöser _____________________________________ 68 Nahaufnahmen ________________________________________ 69 Einbelichten von Datum/Uhrzeit in Aufnahmen (nur Modell Lite Touch Zoom 70W QD) __________________ 70 Weitere Informationen Korrigieren von Datum und Uhrzeit (nur Modell Lite Touch Zoom 70W QD) __________________ 71 Austauschen der Batterie der Datenrückwand...
Teile und Bedienelemente der Kamera (Gehäuse) Makrotaste ( S. 69) Belichtungs- meßfenster Lampe zur Verringerung des “Rote Augen”-Effekts S. 66, 67) Selbstauslöseranzeige Objektiv S. 68) Sucherfenster S. 47) Autofokusfenster Autofokusfenster Schiebeabdeckung (Hauptschalter) S. 49) Blitz( S. 60-67) LC-Display ( S. 46) Batteriefachdeckel S.
Seite 45
Daten) ( S. 71) Taste SEL* (zum Auswählen der Taste MODE* Position der zu (zum Auswählen von korrigierenden Daten) Daten, die einbelichtet S. 71) oder korrigiert werden sollen) ( S. 70, 71) * nur Modell Lite Touch Zoom 70W QD Übersicht...
LC-Display Selbstauslöseranzeige S. 68) Anzeige für Unendlicheinstellung S. 68) Bildzähler ( S. 51) Batterieanzeige ( S. 49) Anzeige für Verringerung des “Rote Augen”-Effekts S. 66, 67) Anzeige für Blitzmodus S. 60-65) Auf den in Klammern angegebenen Seiten finden Sie weitere Erläuterungen. Übersicht...
Anzeigen im Sucher 1Parallaxenausgleichsmarkierungen Für Nahaufnahmen im Makromodus mit einem Abstand von etwa 0,6 m. 2Autofokusrahmen ( S. 55) Das Hauptmotiv muß innerhalb dieses Rahmens scharf gestellt werden. 3Rote LED Leuchtet kurz auf: Der Fokus ist scharf eingestellt. Wenn Sie den Auslöser drücken, wird der Verschluß...
Einlegen der Batterie Batterietyp Verwenden Sie für diese Kamera eine Lithiumbatterie CR2 mit 3 V. Öffnen Sie den Batteriefachdeckel. Öffnen Sie den Batteriefachdeckel in die Richtung, die mit dem Pfeil in der Abbildung angegeben ist. Legen Sie eine neue Batterie ein. Achten Sie auf die richtige Polarität, und legen Sie die Batterie in der in der Abbildung oben dargestellten Richtung ein.
Einschalten der Kamera Öffnen Sie die Schiebeabdeckung. Wenn Sie die Abdeckung in Pfeilrichtung aufschieben, wird die Kamera eingeschaltet, der integrierte Blitz klappt auf, und das Objektiv wird ausgefahren. Wenn die Kamera mehr als 3 Minuten lang nicht bedient wird, wechselt das Objektiv automatisch wieder in die Weitwinkelposition Schieben Sie die Abdeckung so weit auf, bis ein Klicken zu hören ist.
Einlegen eines Films Tips zu 35-mm-Filmen Anzahl der Bilder DX-Code DX-Markierung 35-mm-Film mit DX-Code Filmpatrone Filmempfindlichkeit Verwenden Sie für diese Kamera 35-mm-Filme mit DX-Code. Bei einem Film mit DX-Code wird die Filmempfindlichkeit automatisch eingestellt. Eine automatische Einstellung erfolgt bei den Empfindlichkeiten ISO 100 und ISO 400. (Wenn Sie einen ISO-200-Film oder einen Film ohne DX-Code verwenden, wird die Empfindlichkeit automatisch auf ISO 100 eingestellt.) Achten Sie beim Einlegen oder Herausnehmen eines Films darauf, die...
Seite 51
Ziehen Sie den Filmanfang bis zur roten Markierung heraus. Halten Sie die Filmpatrone fest, und achten Sie darauf, den Film richtig einzulegen. Der Film darf sich nicht nach oben wölben. Schließen Sie die Kamerarückwand, und überprüfen Sie, ob der Film richtig eingelegt wurde.
Probeaufnahmen zu machen, um mit der kamera und all ihren Funktionen vertraut zu werden. Nikon übernimmt keine Haftung für Fehlfunktionen, die darauf zurückzuführen sind, daß die Kamera Lite Touch Zoom 70W/Lite Touch Zoom 70W QD anders als in dieser Anleitung angegeben bedient wurde. Grundfunktionen...
Drücken des Auslösers Drücken Sie die Taste leicht, und vergewissern Sie sich, daß die rote LED leuchtet. Wenn Sie die Taste leicht drücken, werden Fokus und Belichtung eingestellt, und die rote LED leuchtet auf. Die Fokuseinstellung ist fixiert (Fokusspeicherfunktion 58), solange Sie den Auslöser leicht gedrückt halten. Drücken Sie den Auslöser ganz nach unten, um das Bild aufzunehmen.
Zoomen Drücken Sie den Zoom-Hebel, um den Bildausschnitt zu wählen. Drücken Sie den Hebel in die Richtung für Teleaufnahmen (70 mm) oder in die Richtung für Weitwinkelaufnahmen (28 mm). Lassen Sie den Hebel los, wenn das Bild in der gewünschten Größe angezeigt wird.
Aufnehmen Richten Sie die Markierung für den Autofokusrahmen in der Mitte auf das Hauptmotiv. Wenn sich das Hauptmotiv außerhalb des Autofokusrahmens befindet: Wenn sich das Hauptmotiv außerhalb des Autofokusrahmens befindet, können Sie mit der Fokusspeicherfunktion eine präzise Scharfeinstellung erzielen. ( S.
Seite 56
Aufnehmen (Fortsetzung) *1 Wenn die rote LED blinkt, nachdem Sie den Auslöser leicht gedrückt haben, wird der Blitz aufgeladen, und der Auslöser ist blockiert. Drücken Sie erneut leicht auf den Auslöser, und drücken Sie den Auslöser ganz, wenn die rote LED aufhört zu blinken und stetig leuchtet.
Zurückspulen des Films Der Film wird automatisch zurückgespult. Wenn das Ende der Filmrolle erreicht ist, spult die Kamera den Film automatisch zurück. Während der Film zurückgespult wird, wird die Bildnummer im Bildzähler heruntergezählt. Sobald der Film vollständig zurückgespult ist, blinkt “ ”, hört dann zu blinken auf und leuchtet stetig.
Wenn sich das Hauptmotiv nicht in der Bildmitte befindet Fotografieren mit Fokusspeicherung Wenn sich das Motiv, auf das fokussiert werden soll, außerhalb des Autofokusrahmens in der Bildmitte befindet, verwenden Sie die Fokusspeicherfunktion. Bei dieser Funktion bleibt die Fokuseinstellung fest, auch wenn Sie nach dem Einstellen des Fokus den Bildausschnitt verändern.
Schwer fokussierbare Motive Bei Motiven der folgenden Art kann es zu Problemen beim Fokussieren kommen. Fokussieren Sie mit der Fokusspeicherfunktion ( 58) zunächst auf ein anderes Motiv, das sich im gleichen Abstand von der Kamera befindet, und wählen Sie dann den gewünschten Bildausschnitt.
Aufnahmen mit Blitz Auswä h len des Blitzmodus Mit der Taste können Sie einen von fünf Blitzmodi auswählen. : Blitzautomatik ( S. 62) Der Blitz wird automatisch ausgelöst, wenn das Umgebungslicht nicht ausreicht. : Unendlicheinstellung ( S. 68) Für eine höhere Bildschärfe bei Fernaufnahmen oder Landschaften.
Vorgehen bei Aufnahmen mit Blitz Wählen Sie mit der Taste Blitzmodus aus. Da in den Modi (Blitzabschaltung) und (Langzeitsynchronisation) in der Regel eine längere Verschlußzeit gilt, empfiehlt sich die Verwendung eines Stativs, um Verwacklungsunschärfen zu vermeiden. Richten Sie die Kamera auf den gewünschten Bildausschnitt, und drücken Sie dann leicht auf den Auslöser.
So wird der Blitz automatisch ausgelöst Blitzautomatik Der Blitz wird automatisch ausgelöst, wenn das Motiv zu dunkel ist. Vergewissern Sie sich, daß “ ” auf dem LC-Display erscheint. Wenn “ ” nicht angezeigt wird, drücken Sie die Taste bis “ ”...
So schalten Sie den Blitz aus Blitzabschaltung Diesen Modus sollten Sie wählen, wenn die Verwendung eines Blitzlichts verboten ist, zum Beispiel in Museen. Verwenden Sie ein Stativ, oder stellen Sie die Kamera auf einer stabilen, waagerecht Oberfläche auf. Verwenden Sie bei Blitzabschaltung ein Stativ. Da in diesem Modus in der Regel eine längere Verschlußzeit gilt, empfiehlt sich die Verwendung eines Stativs, um Verwacklungsunschärfen zu vermeiden.
So wird der Blitz bei jeder Aufnahme ausgelöst Blitz bei jeder Aufnahme In diesem Modus wird der Blitz unabhängig von den Lichtverhältnissen bei jeder Aufnahme ausgelöst. Drücken Sie die Taste , bis “ ” im LC-Display erscheint. Achten Sie darauf, daß die rote LED aufleuchtet, und drücken Sie dann den Auslöser.
So fotografieren Sie ein Motiv bei Nacht Langzeitsynchronisation Mit diesem Modus werden das Motiv und der Hintergrund bei Aufnahmen in der Nacht oder in der Dämmerung aufgehellt. Verwenden Sie ein Stativ, oder stellen Sie die Kamera auf einer stabilen, waagerecht Oberfläche auf. Verwenden Sie für die Langzeitsynchronisation ein Stativ Da in diesem Modus in der Regel eine längere Verschlußzeit gilt, empfiehlt sich die Verwendung eines Stativs, um...
So verringern Sie den “Rote Augen”-Effekt Modus zur Verringerung des “Rote Augen”-Effekts Bei Blitzaufnahmen erscheinen die Augen einer aufgenommenen Person manchmal leuchtend rot. Verwenden Sie diesen Modus, um diesen “Rote Augen”- Effekt zu verringern. Drücken Sie die Taste , bis “ ”...
Seite 67
Richten Sie die Kamera auf den gewünschten Bildausschnitt, und drücken Sie dann leicht auf den Auslöser. Achten Sie darauf, daß die rote LED aufleuchtet, und drücken Sie dann den Auslöser. Kamera und Motiv dürfen sich nicht bewegen. Die Lampe zur Verringerung des “Rote Augen”-Effekts leuchtet etwa eine Sekunde auf, bevor der Blitz ausgelöst wird.
Fernaufnahmen oder Aufnahmen durch ein Fenster Unendlicheinstellung In diesem Modus können Sie bei Fernsichtaufnahmen eine höhere Bildschärfe erzielen oder Landschaften durch ein Fenster fotografieren. Drücken Sie die Taste , bis “ ” im LC-Display erscheint. Achten Sie darauf, daß die rote LED kurz aufleuchtet, und drücken Sie dann den Auslöser.
Nahaufnahmen Der Mindestabstand zwischen Kamera und Motiv muß bei Teleaufnahmen etwa 0,6 m betragen. Um ein Motiv, zum Beispiel eine Blume, so bildfüllend wie möglich aufzunehmen, können Sie bis auf etwa 0,6 m an das Motiv herangehen. Im Makromodus muß der Abstand zwischen Kamera und Motiv etwa 0,6 bis 1,0 m betragen.
Einbelichten von Datum/Uhrzeit in Aufnahmen (nur Modell Lite Touch Zoom 70W QD) Wählen Sie mit der Taste MODE die Datums-/Uhrzeitanzeige aus. Das Jahr wird mit den ersten beiden Ziffern angegeben (“ ” für 2000, “ ” für 2001) und einbelichtet, und die Uhrzeit wird im 24-Stunden-Format angezeigt.
Korrigieren von Datum und Uhrzeit (nur Modell Lite Touch Zoom 70W QD) Drücken Sie die Taste MODE, so daß Jahr/Monat/Tag angezeigt werden. Drücken Sie die Taste SEL, bis die Angabe blinkt, die Sie korrigieren wollen. Stellen Sie die blinkende Zahl mit der Taste ADJUST ein.
Austauschen der Batterie für die Datenrückwand (nur Modell Lite Touch Zoom 70W QD) Wenn die einbelichtete Datums-/Uhrzeitangabe auf dem Film zu dunkel oder schlecht lesbar ist, ist wahrscheinlich die Batterie erschöpft. Ersetzen Sie sie durch eine neue. Batterietyp Verwenden Sie bei dieser Kamera eine Lithiumbatterie CR2025 mit 3 V als Datumsspeicherbatterie.
Seite 73
Tauschen Sie die Batterie gegen eine neue aus. Legen Sie die neue Batterie wie in der Abbildung gezeigt mit dem Pol nach oben ein. Schließen Sie den Batteriefachdeckel wieder, und bringen Sie die Schrauben wieder an. Ziehen Sie die Schrauben mit einem Schraubenzieher fest. Die eingebaute Uhr wird zurückgesetzt, wenn die Batterie herausgenommen wird.
Fehlersuche Versuchen Sie zunächst, anhand der folgenden Tabelle die Fehlerursache zu ermitteln. Sie ersparen sich damit unter Umständen einen Besuch bei Ihrem Nikon-Kundendienstzentrum. Ursachen und Abhilfemaßnahmen Problem Seite a Die Batterie ist nicht polaritätsrichtig eingelegt. Der Auslöser Legen Sie sie polaritätsrichtig ein.
Seite 75
Problem Ursachen und Abhilfemaßnahmen Seite Die Zahl “ ” a “ ” erscheint im LC-Display, wenn Sie die Kamera einschalten, indem Sie die erscheint nicht, wenn Schiebeabdeckung öffnen. ein Film Nehmen Sie den Film aus der Kamera, 50,51 und legen Sie ihn erneut ein. eingelegt wird.
Blitz auszulösen. Auf diese Weise verhindern Sie, daß die Leistungsfähigkeit der Kondensatoren nachläßt. Schützen Sie die Kamera vor Feuchtigkeit: Die Lite Touch Zoom 70W/Lite Touch Zoom 70W QD ist nicht wasserdicht und darf daher Feuchtigkeit nicht ausgesetzt werden. Schützen Sie die Kamera vor heftigen Erschütterungen:...
Technische Daten Kameratyp 35mm-Kieinbildkamera mit Autofokus, Zentralverschluß und Nikon- Zoom-Objektiv Geeignetes Filmmaterial 35mm-Kieinbildfilm mit DX-Code Bildformat 24 × 36 mm Objektiv 28 mm (f/5,6) bis 70 mm (f/10), 5 Elemente in 4 Gruppen Verschluß Programmierter elektronischer Verschluß Sucher Realbild-Sucher, Bildfeld: ca. über 80% bei normalformatigen Bildern;...
Seite 78
Bildzähler, Blitzmodus, Verringerung des “Rote-Augen”-Effekts, Selbstauslöser, Unendlicheinstellung, Batterieladung Stromquelle Eine Lithiumbatterie CR2 mit 3 V Funktion zur Datumseinbelichtung (nur Lite Touch Zoom 70W 24-Stunden-Anzeige; fünf Anzeigeformate mit Drucktaste wählbar (Jahr/Monat/Tag, Tag/Stunde/Minuten, keine Einbelichtung, Monat/Tag/ Jahr, Tag/Monat/Jahr); Berücksichtigung der Schaltjahre bis 2049;...
Sie sie sofort aus. Lassen Sie die Kamera abkühlen, und nehmen Sie dann die Batterie heraus. Lassen Sie die Kamera über Ihren Nikon-Händler reparieren. • Tauchen Sie die Kamera nicht ins Wasser, und schützen Sie sie vor Spritzwasser und Regen.
Seite 80
Sicherheitshinweise zum Umgang mit der Kamera (Fortsetzung) VORSICHT • Lösen Sie den Blitz nie direkt vor den Augen einer anderen Person aus. Dies könnte zu Blindheit führen. Halten Sie insbesondere beim Fotografieren von Kindern einen Abstand von mindestens 1 m. •...
Nous vous remercions d’avoir fait l’acquisition de cet appareil photo Nikon Lite Touch Zoom 70W / Lite Touch Zoom 70W QD. Lisez attentivement le présent mode d’emploi avant toute utilisation et conservez-le à portée de la main jusqu’à ce que vous soyez suffisamment familiarisé avec votre nouvel appareil.
Seite 83
Utilisation du retardateur ________________________________ 108 Photographie de plans rapprochés ________________________ 109 Impression de la date/heure sur les photos (Lite Touch Zoom 70W QD uniquement) ________________ 110 Informations complémentaires Correction de la date et de l’heure (Lite Touch Zoom 70W QD uniquement) ________________ 111...
Descriptif de l’appareil (Boîtier) Bouton Macro Fenêtre d’exposition p. 109) automatique Illuminateur d’atténuation des yeux rouges ( pp. 106, 107) Témoin du retardateur Objectif p. 108) Oculaire du viseur( p. 87) Fenêtre de mise au point automatique Fenêtre de mise au point automatique Couvercle coulissant (commutateur marche/...
Seite 85
111) Bouton SEL* (pour sélectionner la Bouton MODE* position des données à (pour sélectionner les données à corriger) impressionner ou à corriger) p. 111) pp. 110, 111) * Lite Touch Zoom 70W QD uniquement Démarrage...
Ecran de contrôle CL Indicateur du retardateur Indicateur de mode de mise p. 108) au point sur l’infini p. 108) Compteur de vues ( p. 91) Indicateur de tension de pile insuffisante ( p. 89) Indicateur d’atténuation des yeux rouges pp.
Indications dans le viseur 1Repères de correction de parallaxe Pour les prises de vue en mode Macro à une distance d’environ 0,6 m. 2Repères de zone de mise au point ( p. 95) Centrez dans cette zone le sujet principal à mettre au point. 3Témoin rouge S’allume: Lorsque la mise au point et réglée et...
Installation d’une pile Type de pile Utilisez pour cet appareil une pile au lithium CR2 3V. Ouvrez le couvercle du logement de la pile. Ouvrez le couvercle du logement de la pile dans le sens de la flèche indiquée dans l’illustration. Introduisez une pile neuve.
Mise sous tension de l’appareil Ouvrez le couvercle coulissant. Lorsque vous ouvrez le couvercle coulissant dans le sens de la flèche, l’appareil se met sous tension, le flash intégré quitte de son logement et l’objectif se déploie. Si vous n’actionnez pas l’appareil pendant plus de 3 minutes, l’objectif se rétracte automatiquement sur la position (grand angle).
Chargement d’un film Conseils sur les films 35 mm Nombre de vues Code DX Code DX Film 35 mm codé DX Cartouche de film Sensibilité du film Utilisez avec cet appareil des films 35 mm codés DX. L’appareil règle automatiquement la sensibilité des films codés DX. La sensibilité...
Seite 91
Tirez l’amorce du film jusqu’au repère de positionnement rouge. Maintenez la cartouche du film et assurez-vous que le film est correctement positionné et bien tendu. Refermez le dos de l’appareil et vérifiez si le film est correctement chargé. Si le film a correctement été chargé, l’indication “ ” s’affiche dans le compteur de vues lorsque vous mettez l’appareil sous tension.
La responsabilité de Nikon ne peut être invoquée en cas de dysfonctionnements résultant d’une utilisation du Lite Touch Zoom 70W / Lite Touch Zoom 70W QD non conforme aux instructions spécifiées dans ce manuel. Opérations de base...
Fonctionnement du déclencheur Sollicitez légèrement le déclencheur et vérifiez si le témoin rouge s’allume. Lorsque vous appuyez légèrement sur le déclencheur, l’appareil règle la mise au point et l’exposition, puis le témoin rouge s’allume. La mise au point reste mémorisée (fonction de mémorisation de la mise au point p.
Cadrage au zoom Appuyez sur le bouton de zoom pour composer l’image. Poussez le levier dans la direction de pour des photos en position de téléobjectif (70 mm) ou dans la direction de pour des photos en position de grand angle (28 mm). Relâchez le bouton lorsque vous avez obtenu le cadrage voulu de la scène.
Prise de vues Centrez le sujet principal à l’intérieur des repères de la zone de mise au point automatique. Si le sujet principal se trouve en-dehors des repères de la zone de mise au point: Si le sujet principal se trouve en-dehors des repères de la zone de mise au point, utilisez la fonction de mémorisation de la mise au point.
Seite 96
Prise de vues (suite) *1 Pendant que le témoin rouge clignote alors que le déclencheur est enfoncé à mi-course, le flash se recycle et l’obturateur ne peut être déclenché. Appuyez de nouveau légèrement sur le déclencheur et déclenchez-le dès que le témoin rouge a cessé de clignoter et reste allumé.
Rembobinage du film Le film se rembobine automatiquement. Le rembobinage démarre automatiquement à la fin du film. Pendant le rembobinage du film, le nombre affiché dans le compteur de vues diminue unité par unité. Dès que le rembobinage est terminé, l’indication “...
Si le sujet principal ne se trouve pas au centre de la zone de mise au point Mémorisation de la mise au point Si le sujet à mettre au point se trouve en-dehors des repères de la zone de mise au point, utilisez la fonction de mémorisation de la mise au point qui vous permet de modifier la composition de l’image tout en verrouillant le réglage de la mise au point.
Sujets difficiles à mettre au point Les sujets suivants peuvent s’avérer difficiles à mettre au point. Utilisez la fonction de mémorisation de la mise au point ( 98) pour faire la mise au point sur un autre sujet équidistant de l’appareil, puis composez l’image pour prendre la photo.
Photographie au flash Sélection du mode de flash Vous pouvez sélectionner l’un des cinq modes de flash en appuyant sur le bouton : Flash automatique ( p. 102) Le flash se déclenche automatiquement si le sujet est sombre ou se trouve à contre-jour. : Mise au point sur l’infini ( p.
Procédure de photographie au flash Appuyez sur le bouton pour sélectionner le mode de Flash. Comme l’appareil sélectionne souvent des vitesses d’obturation lentes dans les modes (Flash annulé) et (Flash en synchronisation lente), nous conseillons d’utiliser un trépied pour éviter les risques de bougé. Composez l’image et appuyez légèrement sur le déclencheur.
Déclenchement automatique du flash Mode de flash automatique Le flash se déclenche automatiquement lorsque le sujet est sombre. Assurez-vous que le repère “ ” apparaît dans l’écran de contrôle CL. Si le repère “ ” n’apparaît pas, appuyez sur le bouton jusqu’à...
Pour désactiver le flash Mode de flash annulé Utilisez ce mode dans des endroits tels que des musées où la photographie au flash est interdite. Montez l’appareil sur un trépied ou installez-le sur une surface stable. Utilisez un trépied pour la photographie en mode de flash annulé...
Déclenchement intentionnel du flash Mode de flash imposé Utilisez ce mode pour déclencher volontairement le flash quelles que soient les conditions de luminosité. Appuyez sur le bouton jusqu’à ce que l’indication “ ” apparaisse dans l’écran de contrôle. Vérifiez si le témoin rouge s’allume et prenez la photo.
Pour photographier un sujet la nuit Mode de flash en synchronisation lente Utilisez ce mode pour éclairer le sujet et l’arrière-plan au crépuscule ou la nuit. Montez l’appareil sur un trépied ou installez-le sur une surface stable. Utilisez un trépied pour la photographie en mode de flash en synchronisation lente Comme l’appareil sélectionne souvent des vitesses d’obturation lentes dans ce mode, nous conseillons d’utiliser un trépied...
Atténuation de l’effet des “yeux rouges” Mode d’atténuation des yeux rouges En mode de photographie au flash, il arrive parfois que les yeux du sujet apparaissent rouges vif. Utilisez ce mode pour atténuer cet effet des “yeux rouges”. Appuyez sur le bouton jusqu’à...
Seite 107
Composez l’image et appuyez légèrement sur le déclencheur. Vérifiez si le témoin rouge est allumé et prenez la photo. L’appareil et le sujet doivent rester immobiles. Le témoin de réduction des “yeux rouges” s’allume pendant environ une seconde avant le déclenchement du flash. Veillez à...
Prise de vues à distance ou d’un paysage à travers une vitre Mode de mise au point sur l’infini Ce mode permet de réaliser des prises de vues plus nettes de sujets à distance ou d’un paysage au travers d’une fenêtre. Apuyez sur le bouton jusqu’à...
Photographie de plans rapprochés La distance minimum entre l’appareil et le sujet est d’approx. 0,6 m en mode de téléobjectif Pour photographier un sujet comme une fleur pour qu’elle apparaisse la plus grande possible sur la photo, vous pouvez vous rapprocher jusqu’à environ 0,6 m. La plage de distance entre l’appareil et le sujet en mode Macro est d’environ 0,6 à...
Impression de la date/heure sur les photos (Lite Touch Zoom 70W QD uniquement) Sélectionnez l’indicateur date/heure en appuyant sur le bouton MODE. L’année est indiquée par les deux derniers chiffres (“ ” pour 2000 et “ ” pour 2001) et impressionnée, et l’heure est indiquée suivant le système à...
Correction de la date et de l’heure (Lite Touch Zoom 70W QD uniquement) Appuyez sur le bouton MODE pour afficher l’indication Année/Mois/Jour. Appuyez sur le bouton SEL de façon à ce que l’indicateur à régler se mette à clignoter. Appuyez sur le bouton ADJUST pour régler le chiffre qui clignote.
Remplacement de la pile du dateur (Lite Touch Zoom 70W QD uniquement) Si la date/heure impressionnée sur le film est sombre ou difficilement lisible, c’est que la pile du dateur doit être épuisée. Remplacez-la. Type de pile Utilisez pour le dateur de cet appareil une pile au lithium CR2025 3V.
Seite 113
Remplacez-la par une pile neuve. Installez la nouvelle pile avec la polarité orientée vers le haut comme illustré. Refermez le couvercle du logement de la pile du dateur et resserrez les vis. Serrez correctement les vis à l’aide d’un tournevis. L’horloge intégrée est réinitialisée lorsque vous retirez la pile.
Dépannage Recherchez la cause de la défaillance en consultant le tableau suivant. Cela peut vous épargner un déplacement vers un centre de service après-vente Nikon. Problè m e Points à vérifier et solutions Voir page. a La polarité de la pile est inversée.
Seite 115
Problè m e Points à vérifier et solutions Voir page. Le chiffre “ ” a L’indication “ ” apparaît dans l’écran de ne s’affiche contrôle CL lorsque l’appareil est mis sous pas même si tension en ouvrant le couvercle coulissant. un film a été...
éviter une détérioration des condensateurs. Gardez l’appareil au sec: Le Lite Touch Zoom 70W / Lite Touch Zoom 70W QD n’est pas étanche et ne peut de ce fait pas être exposé à la pluie ou à l’eau saline.
Caractéristiques Type d’appareil Appareil 35 mm autofocus à obturateur et zoom Nikon Films utilisables Cartouches de films 35 mm codés DX Format 24 × 36 mm Objectif 28 mm f/5.6–70 mm f/10, 5 éléments en 4 groupes Obturateur Programmé électroniquement Viseur Viseur zoom à...
Seite 118
CR2025 Dimensions (L × H × P) Approx. 117 × 63 × 42 mm Lite Touch Zoom 70W Lite Touch Zoom 70W QDApprox. 117 × 63 × 47 mm Poids (sans pile) Lite Touch Zoom 70W Approx. 200 g Lite Touch Zoom 70W QDApprox.
à haute tension susceptibles de provoquer des décharges électriques. Retirez la pile et présentez votre appareil à votre revendeur Nikon pour réparation. • Si vous détectez de la fumée sortant de l’appareil, cessez immédiatement toute utilisation et mettez l’appareil hors...
Seite 120
Pour une utilisation sans risque de l’appareil (suite) ATTENTION • Ne déclenchez pas le flash près des yeux d’une personne, car vous risquez de provoquer une cécité. En particulier, gardez une distance d’au moins 1 m lorsque vous prenez des photos d’enfants. •...
Seite 122
Queda prohibida la reproducción total o parcial de este folleto (salvo en lo que se refiere a citas breves en artículos o revistas especializadas), sin la autorización escrita de NIKON CORPORATION. NIKON CORPORATION FUJI BLDG., 2-3, MARUNOUCHI 3-CHOME CHIYODAKU, TOKYO 100-8331, JAPAN...