Programming Keygo Io Remote Controls For Full And Partial Opening Operation; Programming Keytis Io Remote Controls For Full And Partial Opening Operation - SOMFY DEXXO PRO io Serie Installationsanleitung

Dexxo Pro io
Automatic closure time delay
Values 0 to 12 (time delay value = value x 10 s)
2: 20 s
Lighting time delay
Values
6 : 60 s
Comments
integrated light may cut out automatically if it is used for an
a light time delay in excess of 2 mn (t1=12 or 120s) only
when remote lighting is used.
> Programming example: setting the "P7" closure approach
speed (Fig. 39)
Setting up a long soft stop function zone "P7" = 2.
> Special case: adjusting the position of the door for partial
opening (Fig. 40)
P6
- Pressing and holding the "-" button will close the door.
- Pressing and holding the "+" button will open the door.
- OK
- SET
> Forced mode (Fig. 41)
This function makes it possible to manipulate the door at any moment (loss of
- press the "-" button to close it
- press the "+" button to open it.
"-" or "+" button to stop the door.
> Programming a Situo Telis Composio Impresario type remote
control (Fig. 42)
documentation).
[1]. PROG
[2]. PROG
This may take from a few seconds to around a minute depending on the
number of products connected to the system.
8 - PROGRAMMING KEYGO IO REMOTE
CONTROLS FOR FULL AND PARTIAL
OPENING OPERATION
activated (refer to the section entitled "Parameter setting").
When parameter P4 is activated, all the remote control buttons
previously programmed during commissioning become programmed
buttons to partially open the garage door.
The operations to be performed differ according to the desired function for
the memorisation which has already been performed on the button prior to
activation of parameter P4.
> Switch to full opening for a button previously memorised
during commissioning (Fig.43)
[1]. Simultaneously press the large button and the left-hand outer button on
the remote control.
Copyright © 2015 SOMFY ACTIVITES SA. All rights reserved
OK
[2]. Press the remote control button previously memorised during
commissioning within 10 seconds.
The button for full opening has been memorised.
> Memorise a button that has not yet been programmed to
trigger partial opening (Fig.23)
[1]. PROG
seconds).
[2]. Simultaneously press the outer right and outer left buttons on the remote
control.
[3].
The button for partial opening has been saved.
> Memorise a button that has not yet been programmed to
trigger full opening (Fig. 44)
[1]. PROG
seconds).
[2]. Simultaneously press the outer right and outer left buttons on the remote
control.
[3].
opening.
[4]. Simultaneously press the large button and the left-hand outer button on
the remote control.
[5]. Press the remote control button that you wish to use for full opening within
10 seconds.
The button for full opening has been memorised.
9 - PROGRAMMING KEYTIS IO REMOTE
CONTROLS FOR FULL AND PARTIAL
OPENING OPERATION
activated (refer to the section entitled "Parameter setting").
When parameter P4 is activated, all the remote control buttons
on buttons which are used to partially open the garage door.
> Save a button that has not yet been programmed to trigger
partial opening (Fig.45)
[1]. Save the button on the Dexxo Pro (refer to the section on "Programming
[2].
remote control.
The remote control beeps twice.
The button for partial opening has been programmed.
> Switch to partial opening for a button previously saved during
commissioning (Fig. 46)
control.
The remote control beeps twice.
The button for partial opening has been programmed.
> Switch a button previously programmed for partial opening to
full opening (Fig. 47)
control.
The button for full opening has been programmed.
> To determine the operating mode in which a button is
programmed
STOP
STOP
STOP
STOP
10