Jet JCDC-1.5 Bedienungsanleitung Seite 4

2. Read and understand the warnings posted on the
machine and in this manual.
3. Replace warning labels if they become obscured
or removed.
4. This dust collector is designed and intended for
use by properly trained and experienced
personnel only. If you are not familiar with the
proper and safe operation of a dust collector, do
not use until proper training and knowledge have
been obtained.
5. Do not use this dust collector for other than its
intended use. If used for other purposes, JET
disclaims any real or implied warranty and holds
itself harmless from any injury that may result
from that use.
6. Always wear approved safety glasses/face shield
while using this dust collector. Everyday
eyeglasses only have impact resistant lenses; they
are not safety glasses.
7. Keep hair, loose clothing, fingers, and all parts of
body away from openings and moving parts.
8. Wear hearing protection (plugs or muffs) during
extended periods of operation.
9. Some dust created by power sanding, sawing,
grinding, drilling and other construction activities
contains chemicals known to cause cancer, birth
defects or other reproductive harm. Some
examples of these chemicals are:

Lead from lead based paint.

Crystalline silica from bricks, cement and
other masonry products.

Arsenic and chromium from chemically
treated lumber.
Your risk of exposure varies, depending on how
often you do this type of work. To reduce your
exposure to these chemicals, work in a well-
ventilated area and work with approved safety
equipment, such as face or dust masks that are
specifically designed to filter out microscopic
particles.
10. Do not operate this machine while tired or under
the influence of drugs, alcohol or any medication.
11. Make certain the switch is in the OFF position
before connecting the machine to the power
supply. Turn off all controls before unplugging.
12. Make certain the machine is properly grounded.
Connect to a properly grounded outlet only. See
Grounding instructions.
13. Make all machine adjustments or maintenance
with the machine unplugged from the power
source.
14. Remove adjusting keys and wrenches. Form a
habit of checking to see that keys and adjusting
wrenches are removed from the machine before
turning it on.
15. Keep safety guards in place at all times when the
machine is in use. If removed for maintenance
purposes, use extreme caution and replace the
guards immediately
complete.
16. Check damaged parts. Before further use of the
machine, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced.
17. Provide for adequate space surrounding work
area and non-glare, overhead lighting.
18. Keep the floor around the machine clean and free
of scrap material, oil and grease.
19. Keep visitors a safe distance from the work area.
Keep children away.
20. Make your workshop child proof with padlocks,
master switches or by removing starter keys.
21. Give your work undivided attention. Looking
around, carrying on a conversation and "horse-
play" are careless acts that can result in serious
injury.
22. The dust collector is intended for indoor use. To
reduce the risk of electric shock, do not use
outdoors or on wet surfaces.
23. Do not use this dust collector for anything except
wood dust. Materials such as liquids, metal
shavings, metal dust, screws, glass, plastic or rock
can cause sparks and/or damage when coming
into contact with any part of the dust collector.
24. Do not use to pick up anything that is burning or
smoking, such as cigarettes, matches or hot ashes.
25. Do not use to pick up flammable or combustible
liquids such as gasoline, or use in areas where
they may be present.
26. Do not pull or carry by cord, use cord as a handle,
close a door on cord, or pull cord around sharp
edges or corners. Do not run dust collector over
cord. Keep cord away from heated surfaces.
27. Do not use this dust collector with a damaged
cord or plug. If the unit is not working as it should,
has been dropped, damaged, left outdoors, or
dropped into water, return it to a service center.
28. Do not unplug by pulling on cord. To unplug,
grasp the plug, not the cord.
29. Do not use without dust bag and/or filters in place.
30. Do not handle plug or machine with wet hands
31. Do not put any objects into the openings. Do not
use with any opening blocked; keep free of dust,
lint, hair, and anything that may reduce air flow.
4
after maintenance is