Running In The Tool - DeWalt XR LI-ION DCN692 Bersetzt Von Den Originalanweisungen


WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: If the tool has been dropped or you
suspect tool damage perform tool operation
check as defined in the mode selection section of
the manual. If it doesn't perform according to the
manual, stop using the tool and have it serviced at
an Authorized D WALT Service Centre.
e
Proper Hand Position (Fig. G)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
as shown.
Preparing The Tool (Fig. A)
12
1. Remove the battery pack
tool is locked off.
2. Remove all nails from the magazine
3
3. Check if the contact trip
4. Reload the nails to the magazine.
5. Insert battery pack.

WARNING: Do not use the tool if the contact trip or nail
pusher cannot move freely.
NOTICE: NEVER spray or in any other way apply
lubricants or cleaning solvents inside the tool. This can
seriously affect the life and performance of the tool.

Running in the Tool

Please note that this tool requires a run-in period before it
operates with full power due to parts which need to mesh or
wear in together. It may be that the tool does not drive long
nails flush consistently during this period.
Actuating The Tool (Fig. A)
The tool can be operated using one of two modes:
Sequential Action Mode
The sequential action mode is used for intermittent nailing
when very careful and accurate placement is desired. It
also offers the maximum delivery of power for driving the
longest nails.
1. Using the mode selector switch
action mode ( or .
2. Release the trigger safety lock-off
3
3. Push the contact trip against the work surface.
1
4. Pull the trigger switch to actuate the tool.
5. Release the trigger and raise the nailer from the
work surface.
6. Repeat steps 3–5 to actuate the next nail.
18
from the tool and ensure the
7
.
can move freely.
9
, select the sequential
2 .
Contact Trip Mode
DCn692
Contact trip mode (also known as bump mode) is used for rapid
nailing on flat, stationary surfaces and typically most effective for
application driving shorter nails.
1. Using the mode selector switch
action mode ( .
2. Release the trigger safety lock-off
3. To drive a single nail, operate the tool as described for
sequential action:
3
a. Push the contact trip
1
b. Pull the trigger switch
pull with the contact trip pushed against the work
surface will drive one nail.
4. To drive several nails, depress and hold the trigger switch
and then push the contact trip
work surface.

WARNING: Do not keep the trigger depressed when the
tool is not in use. Keep the trigger safety lock-off
locked position to prevent accidental actuation when the
tool is not in use.
5. When changing between sequential and bump modes,
it may be necessary to adjust the driving depth. Refer to
Adjusting the Driving Depth for instructions.
RapidCycle Mode
DCn695
The RapidCycle mode is ideal for when the user fires many nails
in a sequence and needs to move more rapidly. The tool still
operates in a full sequential mode, but the motor readies itself
for the next nail immediately after firing to minimise time spent
waiting for the motor to get up to speed.
1. Use the mode selector switch
mode .
2. Release the trigger safety lock-off
3. To drive a single nail, operate the tool as described in the
sequential action:
3
a. Push the contact trip
1
b. Pull the trigger switch
hear the motor spin up after the nail has been driven).
4. To drive several nails simply repeat the directions in point
3. above. If you do not fire a nail within 2 seconds of the
previous then the motor will coast down to rest.
Using The Trigger Lock-Off (Fig. C)
Each D WALT nailer is equipped with a trigger lock-off
e
when pushed to the right as shown in Figure C, prevents the
tool from firing a nail by locking the trigger and bypassing
power to the motor.
When the trigger lock-off is pressed to the left, the tool will be
fully operational. The trigger lock-off should always be locked
off whenever any adjustments are made or when tool is not in
immediate use.
EnGLIsh
9
to select the bump
2
.
against the work surface.
to actuate the tool. Each trigger
3
repeatedly against the
2
in the
9
to select the RapidCycle
2
.
against the work piece.
to actuate the tool. (You will
2
which
1
,
47