Description (Fig. A); Intended Use; Assembly And Adjustments - DeWalt XR LI-ION DCN692 Bersetzt Von Den Originalanweisungen

nOTE: Battery packs, chargers and kitboxes are not included
with N models. Battery packs and chargers are not included with
NT models. B models include Bluetooth® battery packs.
nOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
such marks by D WALT is under license. Other trademarks and
e
trade names are those of their respective owners.
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Visible radiation. Do not stare into light.
Length of nails.
50-90mm
Nail thickness.
2.8–3.3 mm
Loading capacity.
55
Suitable nail collation angle.
30 - 34˚
Date Code Position
The date code which also includes the year of manufacture, is
printed into the housing.
Example:
2019 XX XX
Year of Manufacture

Description (Fig. A)


WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
1 Trigger
2 Trigger safety lock-off
3
Contact trip
4 Depth adjustment wheel
5 Low battery and jam/stall indicator light
6 Stall release lever
7 Magazine
8 Pusher latch
9 Mode selector switch
10 Rotating rafter/belt hook
11 On-board hex wrench
12 Battery pack
13 No-mar tip
14 Speed selector switch

Intended Use

The DCN692 and DCN695 cordless framing nailers have been
designed for driving nails into wooden workpieces.
The DCN692 cordless framing nailer is designed for sequential/
bump modes. Nailers designed for sequential/bump modes
MUsT nOT be used on scaffoldings, stairs, ladders or ladder-like
constructions, e.g., roof laths. For exemptions check your local
national workplace regulations.
The DCN695 cordless framing nailer is designed for sequential
use only, whether in standard sequential mode, or RapidCycle
sequential mode for faster nailing. Nailers designed for
sequential only mode MaY BE used on scaffoldings, stairs,
ladders or ladder-like constructions, e.g., roof laths.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
These cordless nailers are professional power tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
Inserting And Removing The Battery Pack
From The Tool (Fig. B)
nOTE: Make sure your battery pack
To Install The Battery Pack Into The Tool Handle
12
1. Align the battery pack
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove The Battery Pack From The Tool
15
1. Press the release button
out of the tool handle.
EnGLIsh
WALT battery packs and chargers.
e
12
is fully charged.
with the rails inside the tool's
and firmly pull the battery pack
45