Optional Accessories - DeWalt XR LI-ION DCN692 Bersetzt Von Den Originalanweisungen

EnGLIsh
No-Mar Tip (Fig. A)
When using this tool on materials that you do not want to mark,
such as wood cladding, use the plastic no-mar tip
3
contact trip .
nOTE: For maximum depth of drive, especially with long nails,
the no-mar covered should be removed.
LED Indicator (Fig. A)
Your nailer is equipped with a LED indicator light
of a jam/stall. Also refer to to the Troubleshooting Guide for
further instruction.
JaM/sTaLL COnDITIOn
Rotate the stall release lever to
release. Refer to Stall Release.
Stall Release (Fig. A, C)
If the nailer is used in rigorous application where all available
energy in the motor is used to drive a fastener, the tool may
stall. The driver blade did not complete the drive cycle and the
5
jam/stall indicator will flash. Rotate the stall release lever
on the tool and the mechanism will release. If the driver blade
does not automatically return to the home position, proceed
to Clearing a Jammed Nail. If the unit continues to stall please
review the mode selection, material and fastener length to be
sure that it is not too rigorous an application.
If continuous stalling occurs, review speed selection.
Depending upon the application, a different speed setting may
be necessary.
Clearing a Jammed Nail (Fig. A, C)
If a nail becomes jammed in the nosepiece, the
5
jam/stall indicator light will flash.
nOTE: The jam could be as a result of debris build up in the
nose channel. Please check and clear out any debris as outlined
below immediately if you notice any change of performance in
the tool.
1. Remove battery pack from tool and engage trigger safety
2
lock-off .
2. Slide the spring-loaded pusher latch
magazine to lock it into place and unload nail strip.
11
3. Using the hex wrench
17
bolts at the top of the magazine.
7
4. Rotate the magazine forward.
5. Remove jammed/bent nail, using pliers if necessary. Clear
out any debris in the nail channel if required.
6. If driver blade is in the down position, rotate the stall release
6
lever on the top of the nailer.
nOTE: If the driver blade will not reset after rotating the
stall release lever, manually resetting the blade with a long
screwdriver may be necessary.
7. Rotate the magazine back into position under the nose of
the tool and tighten hex bolts
48
13
over the
5
to alert you
6
8
to the base of the
provided, loosen the two hex
17
.
8. Reinsert battery pack.
nOTE: The tool will disable itself and not reset until the
battery pack has been removed and reinserted.
9. Reinsert nails into magazine (refer to Loading the Tool).
8
10. Release the pusher latch
11. Disengage the trigger safety lock-off
continue nailing.
If nails become jammed in the nosepiece frequently, have the
tool serviced by an authorised D
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
NOTICE: NEVER spray or in any other way apply
lubricants or cleaning solvents inside the tool. This can
seriously affect the life and performance of the tool.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.

Optional Accessories


WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
DCN6901 Return Spring Replacement Kit
(Fig. H–L)
Over time driver blade return springs will wear and eventually
need replacement. It will become apparent that the springs
.
2
when ready to
WALT service centre.
e
WALT recommended
e