Specifications; Standard Equipment; Optional Accessories - Virutex MEB50 Gebrauchsanweisung

2. SPECIFICATIONS

Base measurements......................................860 x 350 mm
Work surface length.................................................800 mm
Work surface height..................................................195 mm
Weight..........................................................................17 kg

3. STANDARD EQUIPMENT

- Auxiliary pressure roller.
- Support guides for inserting and removing the
piece.
- Rear support guide which can be extended up to
500 mm.
- Removable clamp on rear support guide.
• You will find the following inside the box of the
MEB50/MEB150:
• 1 MEB50/MEB150 Worktop for PEB50/PEB150 ed-
gebander.
• 1 rear, extendible support guide, disassembled into
the following parts:
1 rear support bar (A, Fig. 1)
2 Washers (B, Fig. 1)
2 M.8x35 allen screws (C, Fig. 1)
2 Arm supports (D, Fig. 1)
2 Arms (E, Fig. 1)
1 Clamp assembly (F, Fig. 1)
• 1 Bag containing 3 screws (J, Fig. 3) for assembling
the PEB50/PEB150; 2 machine attachments (T and
U, Fig. 3) and 18 worktop attachments (S, Fig. 3), for
edgebanding round pieces; and 5 rear attachments (V,
Fig. 3) for edgebanding curved shapes.

4. OPTIONAL ACCESSORIES

1645916 – Roll-holder for MEB50/MEB150. (Fig. 4)
5045753 - SFV50 stand with 2 suction pads. (Fig. 5 and
6)
5045833 - SFV50 stand with 1 suction pad. (Fig. 5)
5046266 - RC50T Tape Cutter
5. FITTING
5.1 FITTING THE REAR GUIDE PLATE
Insert an arm (E, Fig. 1) in each of the two guides (G,
Fig. 1) attached to the sides of the worktop.
Remove the screws (C, Fig. 1) and the washers (B, Fig.
1) from the arms (E, Fig. 1).
Mount the rear support bar (A, Fig. 1) on the arms E,
and fix it to the supports (D, Fig. 1) using the screws (C,
Fig. 1) and the washers (B, Fig. 1).
Move the rear guide plate into the guides (G, Fig. 1) until
it touches the bar (H, Fig. 1) of the worktop.
Fix the rear support guide in this position with the Levers
(I, Fig. 1) on both sides.
Loosen the screws (C, Fig.1); make the surfaces of the
rear support bar (A, Fig. 1) flush with the bar (H, Fig.
1) on the worktop and tighten the screws (C, Fig. 1) in
this position.
5.2 FITTING EDGEBANDER PEB50/PEB150 TO
THE WORKTOP
Place edgebander PEB50/PEB150 on worktop MEB50/
MEB150 in the position shown in (Fig. 2) and fix it in
place using the three screws (J, Fig. 2).
6. PREPARING EDGEBANDER PEB50/PEB150
Follow the steps indicated in the PEB50/PEB150 ed-
gebander manual exactly to prepare it for gluing the
first edging.
The steps to take in chronological order are listed below
as a reminder:
• Connect the PEB50/PEB150 edgebander to the power
source.
• Turn on the main switch (IG, Fig. 2) to start heating
it up.
• Cut the edging strip to the measurement of the board
to be glued.
• Adjust the edging guide height.
Do not leave the strip in the guides.
temove it when you have finished the
adjustments.
• WHEN THE ADVANCE SWITCH LIGHT (IA, Fig. 2)
COMES ON:
- Check there is enough glue in the machine tank.
- Check the glue flow setting is correct.
• The edgebander is now ready to start gluing ed-
gings.
7. EDGEBANDING STRAIGHT PIECES
Prior adjustments:
Ensure that the support guides (M and L, Fig. 1) are in
the right position:
• The exiting support guide (M, Fig. 7) should be in
line with the two rollers (P and N, Fig. 7). If it is not,
you can align it by loosening the screws (R, Fig. 2) that
hold it in place.
• To check that the intake guide (L, Fig. 7) is positioned
correctly, place a piece of the strip you are going to
edgeband against the rollers (P and N, Fig. 7). Press a
straight panel against these and ensure that the intake
Guide (L, Fig. 7) is in line with the clean edge of the
panel. If it is not, align it by loosening the screws (R,
Fig. 2) that hold it in place.
Place the clamp (F, Fig. 7) in position:
If you wish to edgeband with the help of the clamp (F,
5