Intended Use; Technical Description - Dometic TRT120E Montage- Und Bedienungsanleitung

Component
DC power cable
Tool bag
Plastic nuts
M8 x 50 hexagon bolt
M8 flat washer
M8 split washer
Rail cap
U-shaped bracket
Spare pole for manual setup
L-shaped hexagonal wrench
Screw driver

Intended use

This rooftop tent is suitable for:
• mounting on a suitable roof rack on the rooftop of a suitable vehicle
• light to moderate weather
• touring
This rooftop tent is not suitable for:
• use by persons with reduced physical, sensory or mental capabilities
• very strong winds or snowfall
• seasonal pitch or commercial use
This product is only suitable for the intended purpose and application in
accordance with these instructions.
This manual provides information that is necessary for proper installation
and/or operation of the product. Poor installation and/or improper oper-
ating or maintenance will result in unsatisfactory performance and a possi-
ble failure.
The manufacturer accepts no liability for any injury or damage to the prod-
uct resulting from:
• Incorrect assembly or connection, including excess voltage
• Incorrect maintenance or use of spare parts other than original spare
parts provided by the manufacturer
• Alterations to the product without express permission from the manu-
facturer
• Use for purposes other than those described in this manual
Dometic reserves the right to change product appearance and product
specifications.
The radio equipment of the device complies with the requirements of the
directive 2014/53/EU. You can find the Declaration of Conformity of the
device on documents.dometic.com.

Technical description

This rooftop tent is equipped with an electrical motor and a wireless
remote control for setting up and folding down. The electrical motor is
equipped with an overheat protection.
The rooftop tent can also be set up manually, using the supplied spare
poles.
The rooftop tent includes a high-density foam mattress.
For transport on the rooftop of a vehicle, the rooftop tent can be folded
down and covered with the supplied tent cover.
EN
Control elements
Quantity
No. in fig. 1,
1
page 3
1
1
8
2
8
3
8
8
4
Using the rooftop tent
4
!
2
2
1
A
Before first use
Familiarize yourself with the product by carrying out a test set up before
the product is used for the first time. Check if the scope of delivery is
complete.
Mounting the rooftop tent
!
Mounting for electrical setup
➤ Proceed as shown (fig. 2, page 3 – fig. 4, page 3).
Mounting for manual setup
➤ See chapter "Setting up the rooftop tent manually" on page 10.
Setting up the rooftop tent
Setting up the rooftop tent electrically
!
<
I
4445103491
Description
UP button
DOWN button
STOP button
WARNING! Risk of injury
• Make sure the rooftop tent is firmly attached to the roof
rack before climbing the ladder.
• Make sure the ladder is hooked into the rooftop tent's
base frame firmly before you enter or leave the rooftop
tent.
• Always climb the ladder with caution.
• Close the rooftop tent's entrance door before you go to
sleep to prevent falling out of the rooftop tent while
sleeping.
• Only use the remote control to control the rooftop tent
from the ground.
NOTICE! Damage hazard
Keep the side windows open while setting up or folding
down the rooftop tent.
WARNING! Risk of injury
• Make sure no other persons, especially children, are
near the vehicle when you and your helper lift the roof-
top tent onto the rooftop of the vehicle.
• Lift the rooftop tent onto the rooftop of your vehicle
together with another capable person to prevent the
rooftop tent from falling down.
• Mount the rooftop tent parallel to the road line and not
at an angle to avoid creating excessive lifting force.
• Fix all bolts so they are sufficiently secured.
WARNING! Risk of injury
Disconnect the DC power cable from the power supply after
setting up the rooftop tent.
NOTE
If the electrical setup does not work, set up the rooftop tent
manually (see chapter "Setting up the rooftop tent manually"
on page 10).
Explanation
Sets up the rooftop tent.
Folds the rooftop tent down.
Stops the setup and folding
process.
9