Product Description And Specifications; Intended Use; Product Features - Würth EWS 7-115 BASIC Originalbetriebsanleitung

the line of cut and near the edge of the workpiece on both
sides of the wheel.
Use extra caution when making a "pocket cut"
r
into existing walls or other blind areas. The pro-
truding wheel may cut gas or water pipes, electrical wiring
or objects that can cause kickback.
Safety Warnings specific for Sanding operations
Do not use excessively oversized sanding disc
r
paper. Follow manufacturers recommendations,
when selecting sanding paper. Larger sanding pa-
per extending beyond the sanding pad presents a lacera-
tion hazard and may cause snagging, tearing of the disc,
or kickback.
Safety Warnings specific for Wire Brushing
operations
Be aware that wire bristles are thrown by the
r
brush even during ordinary operation. Do not
overstress the wires by applying excessive load
to the brush The wire bristles can easily penetrate light
clothing and/or skin.
If the use of a guard is recommended for wire
r
brushing, do not allow any interference of the
wire wheel or brush with the guard. Wire wheel
or brush may expand in diameter due to work load and
centrifugal forces.
Additional safety information
Wear safety goggles.
Use suitable detectors to determine if utility
r
lines are hidden in the work area or call the
local utility company for assistance. Contact with
electric lines can lead to fire and electric shock. Damaging
a gas line can lead to explosion. Penetrating a water line
causes property damage or may cause an electric shock.
Do not touch grinding and cutting discs until
r
they have cooled down. The discs can become very
hot while working.
Release the On/Off switch and set it to the off
r
position when the power supply is interrupted,
e. g., in case of a power failure or when the
mains plug is pulled. This prevents uncontrolled restart-
ing.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
20
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Secure the workpiece. A workpiece clamped with
r
clamping devices or in a vice is held more secure than by
hand.
Use only original Würth accessories.
r
Product Description and
Specifications
Read all the safety and general instruc-
tions. Failure to observe the safety and general
instructions may result in electric shock, fire and/
or serious injury.
Please observe the illustrations at the beginning
of this operating manual.

Intended use

The power tool is intended for roughing metal, stone and
ceramic materials and for drilling tiles.
With approved abrasive tools, the power tool can be used for
sanding with sanding discs.
A special protective guard for cutting must be used when cut-
ting bonded abrasives.
Sufficient dust extraction must be provided when cutting stone.
Together with the hand guard (accessory), the power tool can
be used for brushing and sanding with elastic sanding pads.
The power tool is suitable only for working without water.
The user is liable for damage incurred as result of using the
tool in any way other than that intended.

Product Features

The numbering of the product features refers to the diagram of
the power tool on the graphics page.
(1) Spindle lock button
(2) On/off switch
(3) Speed preselection thumbwheel (EWS 7-125 E BASIC)
(4) Auxiliary handle (insulated gripping surface)
(5) Combination wrench for grinding spindle
(6) Locking screw for protective guard
(7) Protective guard for grinding
(8) Protective guard for cutting
(9) Mounting flange with O‑ring
(10) Grinding disc/cutting disc
A)
(11) Carbide grinding head
(12) Clamping nut
A)
(13) Quick-clamping nut
A)
A)