Inhaltsverzeichnis
Werbung
GB
•
Press the spindle lock (6) and turn the spindle
(9) until it engages in the lock. Keep the
spindle lock pressed during this procedure.
•
Remove the flange nut (12) from the spindle
using the spanner (11).
•
Position the grinding disc (7) on the flange (5).
•
Place the flange nut on the spindle an tighten
it using the spanner.
•
Release the spindle lock and check that the
spindle is unlocked by rotating it.
Mounting the side handle
Fig. A
The side handle can be used for both left-hand
and right-hand control.
•
Fasten the side handle (5) for left-hand
operation on the right-hand side of the
machine.
•
Fasten the side handle for right-hand
operation on the left-hand side of the
machine.
•
Fasten the side handle for upright working at
the top of the machine.
Make sure that the side handle is
fastened properly and cannot loosen
unexpectedly.
4. USE
Always observe the safety instructions
and applicable regulations.
Do not place the machine on the workpiece when
switching the machine on or off. The grinding
disc may damage the workpiece.
•
Clamp the workpiece and make sure that the
workpiece cannot slide from under the
machine during the cutting activities.
•
Hold the machine firmly and press it under an
angle of approximately 15˚ against the
workpiece. Move the grinding disc evenly
across the workpiece.
•
Regularly inspect the grinding disc. Worn
grinding discs have a negative effect on the
efficiency of the machine. Replace a grinding
disc on time.
•
Always switch off the machine first before
removing the plug from the wall socket.
06
Switching on and off
•
This machine is equipped with a safety
switch. Start the machine by pressing the
"lock off" button (to disengage the switch) and
switch on the machine.
Before start working, the machine must
be run according to the max. speed.
•
Always put the angle grinder in zero load
(without load) when you connect or
disconnect.
•
Always keep the mains lead away from
moving parts.
•
During the grinding you have to work under
an angle between 10° and 15°, so that you
get in touch with splashing sparks as few as
possible. During cutting between 30° and 45°.
Do not put the machine down when the motor is
still running. Do not place the machine on a dusty
surface. Dust particles may enter the
mechanism.
Never use the spindle lock to stop the
motor.
Never use the machine for grinding
magnesium workpieces.
5. MAINTENANCE
Make sure that the machine is not live
when carrying out maintenance work on
the motor.
The machines have been designed to operate
over a long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends upon proper machine care and regular
cleaning.
Trouble shooting
Should the machine fail to function correctly, a
number of possible causes and the appropriate
solutions are given below:
1. Machine fails to operate
•
Power turned off.
•
(Extension) cable damaged.
Ferm
VINKELSLIBER
Tallene i den følgende tekst korresponderer
med afbildningerne på side 2 - 3.
Læs denne brugsanvisning godt
igennem før maskinen tages i brug.
Sørg for at De kender maskinens
funktion og betjening. Vedligehold
maskinen i følge instruktionerne, for at
maskinen altid kan fungere optimalt.
Bevar denne brugsanvisning og den
vedlagte dokumentation til maskinen.
Indhold
1. Tekniske specifikationer
2. Sikkerhedsforskrifter
3. Samling
4. Anvendelse
5. Service & vedligeholdelse
1. TEKNISKE
SPECIFIKATIONER
Tekniske data
Spænding
230 V~
Frekvens
50 Hz
Optaget effekt
1400 W
Antal slag, ubelastet
10000/min
Skivediameter
125 mm
Akselmål
M14
Vægt
3.41 kg
Lpa (lydtryk)
90.5 dB(A)
Lwa (lydevne)
103.5 dB(A)
Vibrationsværdi
3.4 m/s
2
Emballagens indhold
1
Vinkelsliber
1
Sidehåndgreb
1
Klampernøgle
1
Kontaktkullene
1
Brugsanvisning
1
Sikkerhedsfolder
1
Garantikort
Kontroller maskinen, løsdele og tilbehør for
transportskade.
Komponenter
Fig. A
1. Ænd/sluk-kontakt
Ferm
2. Gevindsokkel kulbørste (begge sider)
3. Aksellås
4. Slibeskive
5. Sidehåndgreb
6. Knappen udløs
2. SIKKERHEDSFORSKRIFTER
I denne brugsanvisning anvendes de følgende
piktogrammer :
Betegnelse for risiko for personskader,
dødsfald eller beskadigelse af værktøjet
i tilfælde af at du er uopmærksom på
instruktioner i denne manual.
Indikerer farer for elektrisk stød
Brandfare
Spindellåsen må kun bruges, når
maskinen ikke kører.
Hold omkringstående på afstand
Brug beskyttelsesbriller og høreværn
Bær beskyttelseshandsker
Særiges sikkerhedsforanstatninger
•
Kontrollér, at det maksimale omdrejningstal,
der er angivet på slibeskiven, stemmer
overens med maskinens maksimale
omdrejningstal.
•
Maskinens omdrejningstal må ikke være
højere end den på slibeskiven angivne værdi.
•
Vær opmærksom på, at slibeskivens mål
stemmer overens med maskinens
specifikationer.
•
Vær opmærksom på, at slibeskiven er
monteret rigtigt og ordentligt spændt fast.
Brug ikke reduktionsringe eller adaptere for at
få en slibeskive til at passe.
•
Brug og opbevar slibeskiver i henhold til
leverandørens anvisninger.
DK
43
Werbung
Inhaltsverzeichnis
