Inglesina ELECTA Bedienungsanleitung Seite 35

FEEDING BOTTLE HOLDER
The chassis is equipped with a standard feeding bottle
holder (J).
fig. 21 To fasten the feeding bottle holder, place the upper
guide in correspondence of the hook (J1) on the chassis and
push it in its housing until it is fully attached.
ADDITIONAL CARRYING UNITS FOR CHASSIS: CARRYCOT,
STROLLER SEAT AND CAR SEAT (IF PRESENT)
fig. 22 The chassis can be used with the Electa carrycot,
the Electa stroller seat and the Cab 0+ / Darwin Infant i-Size
car seat, if present.
ELECTA CARRYCOT
ATTACHING THE CARRYCOT TO THE CHASSIS
fig. 23 Take the carrycot from the handle and attach it to
the chassis in correspondence of the housings on both sides
of the structure and place it solely facing the parents.
fig. 24 Once the carrycot is installed, check that the
indicators (C1) on both the attachment devices are Green.
If they are Red, reposition the carrycot correctly until the
indicators turn Green.
fig. 25 Caution: before use, make sure that the carrycot
is properly attached on both sides by pulling it upwards.
DETACHING THE CARRYCOT FROM THE CHASSIS
fig. 26 Operate the lever (C2) located outside the carrycot
and simultaneously lift it, gripping it by the handle.
FITTING THE HOOD LINING
fig. 27 Wrap the hood lining (C) around the handle, fixing
it with the dedicated buttons (C3) and with the central Velcro
fastening strap (C4).
fig. 28 Complete the fitting by attaching the side and rear
Velcro fastenings (C5) to the carrycot.
HANDLE AND HOOD ADJUSTMENT
fig. 29 To adjust both the handle and the carrycot hood,
press the two internal buttons simultaneously (C6).
fig. 30 Caution: Before carrying or lifting the carrycot,
always check that the handle is in its vertical position and
properly locked on both sides.
ATTACHING THE APRON
fig. 31 To fit the cover (D) hook the zip fastening to the
carrycot and button the flap to the hood.
fig. 32 The front flap of the apron (D1) can be extended
and fixed in a position that protects your child from the cold.
fig. 33 The double-slider zip on the cover allows easy
access to the child.
BACKREST ADJUSTMENT
fig. 34 Operate the lever (C6) to adjust the backrest: once
the desired position is reached, set the lever to the starting
position.
CARRYCOT VENTILATION
The Electa carrycot features a coordinated ventilation system.
fig. 35 The ventilation of the base can be adjusted using
the lever (C7) at the front.
fig. 36 If present: the mesh insert on the hood permits
greater circulation of air inside the carrycot.
MATTRESS AND INTERNAL LINING MAINTENANCE
It is advisable to remove the mattress and internal lining
periodically for correct maintenance.
fig. 37 To remove the internal lining simply release it from
the edge of the carrycot.
CARRYCOT LINING MAINTENANCE
fig. 38 If it is necessary to remove the carrycot cover,
simply pull it off by unfastening the perimeter straps from
the seats on the structure.
fig. 39 When refitting it, ensure that the two elastic loops
(C8) are fitted perfectly underneath the lower tabs (C9) on
both attachment devices.
Caution! Incorrect positioning of the elastic loops could
interfere with correct attachment of the carrycot to the
chassis.
ELECTA STROLLER SEAT
ATTACHING THE STROLLER SEAT TO THE CHASSIS
fig. 40 Attach the stroller seat (E) to the chassis,
positioning it in the dedicated housings on both sides of the
structure.
ADJUSTING THE BACKREST
fig. 41 The backrest can be adjusted to 4 positions; use
the central device (E2) and bring the backrest to the desired
position.
fig. 42 Caution: do not use the stroller with the
backrest reclined against the handlebar.
fig. 43 Caution: before use, make sure that the stroller
seat is properly attached on both sides by pulling it
upwards.
DETACHING THE STROLLER SEAT FROM THE CHASSIS
fig. 44 Operate the lever (E1) and simultaneously lift the
stroller seat from the chassis.
Caution: do not, under any circumstance, carry out this
operation with the baby inside.
fig. 45 The stroller seat can be used both facing the parent
and facing the street.
ADJUSTING THE FOOTREST
fig. 46 To lower the footrest, use both levers (E3)
positioned on the lower part and simultaneously press them
downwards.
fig. 47 To lift the footrest, simply pull it upwards and it
shall automatically lock into position.
SAFETY BELTS
fig. 48 Ensure that the safety belts are inserted in the
eyelets at the height of the shoulders or immediately above.
If the position is not correct, remove the belts from the first
pair of eyelets and reinsert them in the second one.
Position both back straps always at the same height.
fig. 49 Connect the ends of the waist straps (E5) to the
back harness (E4) and complete the attachment by inserting
the end pieces into the central buckle (E6).
fig. 50 Always use the waist strap together with the back
harness, adjusting both of them properly.
Caution! Failure to observe this precaution could cause
your baby to fall or slip, risking injury.
Caution: adapt the height and the length of the harness
according to the baby's growth.
ATTACHING THE HANDRAIL
fig. 51 To attach the bumper bar (F), fit it in the dedicated
housings (F2) in the stroller seat until it clicks into place.
fig. 52 The handrail can be open on one side or fully
removed; to open it, press the button (F1) and remove it from
its housing; to remove it, repeat the procedure on the other
side.
STROLLER HOOD
fig. 53 To adjust the hood (G), simply accompany it to the
desired position.
fig. 54 The hood features an additional fabric insert
and sun shade that extend the degree of cover, improving
protection from the sun.
35