Inglesina ELECTA Bedienungsanleitung Seite 34

Handwash in cold water
Do not bleach
Do not tumble dry
Dry flat in shade
Do not iron
Do not dry clean
Do not spin-dry
LIST OF COMPONENTS
fig. 1
ELECTA CHASSIS
A Rear wheels
B Front wheels assembly
ELECTA CARRYCOT
C Hood lining
D Carrycot apron
ELECTA STROLLER
E Stroller seat
F Handrail
G Hood
ACCESSORIES
J Feeding bottle holder
H Storage basket
K Muff (if available)
L Rain cover (if available)
CAB 0+ / DARWIN INFANT i-SIZE CAR SEAT
(IF AVAILABLE)
STANDUP (IF AVAILABLE)
ELECTA CHASSIS
CHASSIS OPENING
fig. 2 Holding the lever (T1) down, lift the chassis firmly
until it opens completely.
fig. 3 Caution: ensure that all locking mechanisms
are properly engaged on both sides before use and that
none of the red indicators are visible.
ASSEMBLING/REMOVING THE REAR WHEELS
fig. 4 Insert the rear wheels (A) into the seats on the
chassis and push them until they click into place.
fig. 5 Caution: make sure that the wheels are properly
attached before use.
Should it be necessary, the rear wheels can easily be removed.
fig. 6 To remove the rear wheel (A) act on the lever (A1)
and at the same time extract it from its seat on the chassis.
REMOVING/ASSEMBLING THE FRONT WHEEL ASSEMBLY
Should it be necessary, both front wheel assemblies (B) can
easily be removed.
fig. 7 Pushing the small button (B1), pull the wheel
34
• Dry the textile lining completely before using or storing it.
• To prevent formation of mildew, it is advisable to air the
carrycot periodically. In particular, separate the textile lining
from the structure and run a dry cloth over the bottom.
INSTRUCTIONS
assembly out from its housing in the support.
fig. 8
clicks into place.
fig. 9
attached before use.
CLOSING THE CHASSIS
fig. 10
handlebar to the lowest position.
fig. 11
the rear handle (T4) until the chassis closes completely.
Caution: always check that the chassis is closed correctly.
fig. 12
(T4).
Never lift the chassis by the handlebar.
REAR WHEELS BRAKE
fig. 13
fig. 14
Always engage the brake during stops.
fig. 15
levers, only press them.
BLOCKING/UNBLOCKING THE FRONT WHEELS
The chassis features swivel wheels.
fig. 16
aligned, then operate the lever (B2) located on both front
wheel units.
ADJUSTING THE HANDLEBAR
The chassis is equipped with an adjustable handle.
fig. 17
raise or lower the handlebar to the desired position.
STORAGE BASKET
The chassis is equipped with a large storage basket (H),
which can be easily removed if necessary.
fig. 18
(H1) that secure it to the side tubes and detach the Velcro
flap (H2) from the spacer tube.
fig. 19
corresponding seats.
fig. 20
off the chassis footboard, then remove the basket from the
small front hooks (H5).
To reinstall the basket, carry out the above operations in
reverse.
To reinstall it, simply position it and push it until it
Caution: make sure that the wheels are properly
Using both adjustment buttons (T2), bend the
Press the button (T3) and simultaneously rotate
To transport the closed chassis, use the rear handle
To operate the brake, press on the right lever (T5).
To release the brake, press on the left lever (T6).
Caution: never lift the brake action and release
To lock or unlock them make sure they are correctly
Operate both buttons (T2) and simultaneously
To remove the basket, undo the 4 snap fasteners
Remove the two rear hooks (H3) from their
Release both front Velcro flaps (H4) and pull them