Proper Use; Remaining Hazards - Scheppach 5903304901 Originalanleitung

– Damaged switches must be replaced at a cus-
tomer service workshop.
– Do not use any faulty or damaged connection
cables.
– Do not use any electric tool on which the switch
cannot be switched on and off.
21 ATTENTION!
– The use of other insertion tools and other acces-
sories can entail a risk of injury.
22 Have your electric tool repaired by a qualified
electrician
– This electric tool conforms to the applicable safe-
ty regulations. Repairs may only be performed by
an electrician using original spare parts. Other-
wise accidents can occur.
Additional safety rules for the belt and disc sanding
machine
• WARNING: Do not use your machine until it is com-
pletely assembled and installed according to the in-
structions.
• If you are not familiar with the operation of the sanding
machine, ask the head of the department, your teacher,
or any other qualified person.
• ATTENTION: This machine has only been designed for
sanding wood or similar materials. The sanding of other
materials can cause fire, injuries, or damage the prod-
uct.
• Always wear safety goggles.
• This machine may only be operated indoors.
• IMPORTANT: Mount and use the machine on a hori-
zontal surface. A non-horizontal surface can damage
the motor.
• If the machine tends to tilt or walk (especially when
sanding long and heavy panels), it must be fastened to
a solid surface of sufficient carrying force.
• Make sure the sanding belt runs in the correct direction
– see arrows at the back of the belt.
• Make sure the sanding belt is running correctly so that
it cannot come off the drive pulleys.
• Make sure the sanding belt is not twisted or loose.
• Firmly hold the workpiece when sanding.
• Always use the fence when using the sanding machine
in horizontal position.
• Always hold the workpiece firmly to the table when us-
ing the sanding disc.
• Always hold the workpiece to the side of the sanding
disc running downwards, in order to maintain the work-
piece pressed to the table. By using the upward-running
side of the sanding disc, the workpiece could be ejected
and cause injury to persons.
• Always keep a minimum distance of about 1.5 mm or
less between the table or fence and the sanding belt or
disc.
• Do not wear gloves. Do not hold the workpiece with a
cloth during sanding.
• Use sanding belt or disc of the correct grit correspond-
ing with the wood.
• Never sand workpieces too small to be held safely.
• Avoid awkward hand positions where a sudden slip
could cause your hand to touch the sanding belt or disc.
• When sanding a large piece of material, provide an ad-
ditional support at table height.
• Never sand an unsupported workpiece. Secure the
workpiece with the table or the fence. Exceptions are
the sanding of curved workpieces on the outside of the
sanding disc.
• Always clear the table, fence or sanding belt of scraps
or other objects, before turning the machine on.
• Do not perform any layout assembly or set-up work on
the table while the sanding machine is in operation.
• Switch the machine off and pull the power plug from the
socket when fitting or removing accessories.
• Never leave the working area of the sanding machine
while the tool is running, or as long as it has not come
to an absolute standstill.
m Proper Use
The machine meets the currently valid EU machine
directive.
• The manufacturer's safety, operation and maintenance
instructions as well as the technical data given in the
calibrations and dimensions must be adhered to.
• Relevant accident prevention regulations and other
generally recognized safety and technical rules must
also be adhered to.
• The machine may only be used, maintained or repaired
by trained persons who are familiar with the machine
and have been informed about the dangers. Unauthor-
ized modifications of the machine exclude a liability of
the manufacturer for damages resulting from the modi-
fications.
• The machine is intended for use only with original spare
parts and original tools from the producer.
• Any other use is considered to be not intended. The
manufacturer excludes any liability for resulting dam-
ages, the risk is exclusively borne by the user.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the equip-
ment is used in commercial, trade or industrial busi-
nesses or for equivalent purposes.
m Remaining hazards
The machine has been built using modern technology and
in accordance with recognized safety rules.
Some hazards, however, may still remain.
• The grinding wheel poses a danger of injury to fingers
and hands by improper feeding or placement of tools.
• Danger of injury from thrown tools due to improper hold-
ing or feeding.
• The use of incorrect or damaged mains cables can lead
to electrical injuries.
• Although having regarded all considerable rules there
may still remain not obvious remaining hazrds.
• Minimize remaining hazards by following the instruc-
tions in "Safety Rules", "Use only as authorized" and in
the entire operating manual.
Commissioning
Installing sanding disc and disc guard, Fig. 4
WARNING: Do not connect to power supply until assem-
bly is complete. Failure to comply could result in acciden-
tal starting and possible serious injury.
• Align perimeter of sanding disc with plate and press
firmly into position.
english 11