Protecting The Environment - DeWalt DW729KN Originalanweisung

7. Switch on and slowly pull the blade through the fence and the workpiece.
8. Return the blade to rest position and switch off.
Mitre Cuts (Fig. HH, II)
1. Release the mitre latch lever 10 and the mitre clamp lever
2. Swing the arm to the required angle on the mitre scale.
3. For 45 ° left or right, engage the mitre latch lever
lever .
11
4. For intermediate angles, use the mitre clamp lever only.
5. Proceed as for cross‑cutting.
Bevel Cuts (Fig. GG, JJ)
1. Set the arm as for a 0 ° cross‑cut.
2. Raise the blade well above the table surface.
3. Release the bevel clamp lever
57
4. Tilt the motor to the required angle on the bevel scale
5. For 45 ° right, engage the bevel latch
6. For intermediate angles, use the bevel clamp lever only.
7. Proceed as for a vertical cross‑cut.
Compound Mitre (Fig. II)
This cut is a combination of a mitre and a bevel cut.
1. Set the required bevel angle.
2. Swing the arm to the required mitre position.
3. Proceed as for mitre cuts.
MAINTENANCE
Your D WALT power tool has been designed to operate over a long period of time with a
e
minimum of maintenance. Continuous satisfactory operation depends upon proper tool care
and regular cleaning.
NOTE: No service is needed on mechanical brake.
IMPORTaNT: Replace the fixed table top and fence when worn.

WARNING: To reduce the risk of serious personal injury, turn tool off and
disconnect tool from power source before making any adjustments or removing/
installing attachments or accessories. Be sure the trigger switch is in the OFF position.
An accidental start-up can cause injury.

WARNING: if the saw blade is worn replace it with a new or re-sharpened blade.
C
Lubrication
Your power tool requires no additional lubrication.
Cleaning
Before use, carefully check the upper blade guard, movable lower blade guard as well as
the dust extraction tube to determine that it will operate properly. Ensure that chips, dust or
workpiece particle cannot lead to blockage of one of the functions.
In case of workpiece fragments jammed between saw blade and guards disconnect the
machine from the power supply and follow the instructions given in section Mounting the
Saw Blade. Remove the jammed parts and reassembling the saw blade.

WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear approved eye protection and approved dust
mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic
parts of the tool. These chemicals may weaken the materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.

WARNING: To reduce the risk of injury, regularly clean the table top.

WARNING: To reduce the risk of injury, regularly clean the dust collection system.
Dust Extraction

WARNING: Always connect a dust extraction device designed in accordance with
relevant regulation regarding dust emission. The air velocity of external connected system
shall be 20m/s +/–2m/s. Velocity to be measured in the connection tube at the point of
connection, with the tool connected but not running.
Transporting (Fig. KK)
To transport the machine be sure the saw head is safely locked. Please be aware the table is
not suitable to lift the machine up. Always use a fork‑lift for transporting.
1. Remove all bolts anchoring the machine to the floor.
NOTE: Ensure the forks are long enough to support the legs and machine.
2. From behind the unit, fully insert the forks under the base to balance the weight of the
machine as shown in Figure KK. Avoid contact with the dust chute and main switch box.
11 .
10 and lock with the mitre clamp
and pull out the bevel latch .
58
.
23
58 and lock with the bevel clamp lever
Optional Accessories

WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only D
Consult your dealer for further information on the appropriate accessories.
Recommended saw blade DW729 ‑ DT4305

Protecting the Environment

Separate collection. Products marked with this symbol must not be disposed of
w
with normal household waste.
Products contain materials that can be recovered or recycled reducing the demand
for raw materials. Please recycle electrical products according to local provisions.
Further information is available at www.2helpU.com.
57 .
WALT recommended accessories should be used with this product.
e
ENGLIsh
WALT, have not been tested
e
27