Package Contents; Description (Fig. A) - DeWalt DW729KN Originalanweisung

Three-phase machines
Please ensure the cable is provided with CEE 16A industrial plug/coupler 5 poles (neutral must
be connected) according to IEC 60309.
Voltage Drops
Inrush currents cause short‑time voltage drops. Under unfavourable power supply conditions,
other equipment may be affected.
If the system impedance of the power supply is lower than 0.25 Ω, disturbances are unlikely
to occur.
Sockets used for these machines shall be fused with 16 Amperes cut‑out with an
inert characteristic.

Package Contents

The package contains:
1 Partly assembled radial arm saw
2 Table strips (1 right,1 left)
2 Fences (1 right, 1 left)
2 Table extensions (1 right, 1 left)
1 SA switch box with electronic brake, overload protector and main switch disconnector
1 Dust shroud
1 Box containing:
1 legstand (4 legs, 1 SA height adjustment crank, 3 M8 x 25)
1 Instruction manual
3 Skinpacks
1 Skinpack containing:
12 D10 flat washers
12 M10 nuts
12 socket head screws M10 x 20
1 Skinpack containing:
4 Triangular supports (2 right, 2 left)
4 Straight supports
6 wood inserts
10 M8 x 25 bolts (aluminium)
19 M8 x 20 bolts
3 D8 (external diameter is 24 mm) washers
26 D8 flat washers
27 nuts M8
1 Skinpack containing:
6 hex keys (3, 4, 5, 6, 8 and 10 mm)
1 pin wrench
3 box spanners (10, 13 and 17 mm)
• Check for damage to the tool, parts or accessories which may have occurred during transport.
• Take the time to thoroughly read and understand this manual prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
a
Read instruction manual before use.
g
Wear ear protection.
f
Wear eye protection.
When the power cord is damaged disconnect the plug from the power
source immediately.
Always disconnect the plug before making any adjustments or perform service/
maintenance.
Date Code Position (Fig. A)
The date code , which also includes the year of manufacture, is printed into the housing.
62
Example:
Year and week of Manufacture

Description (Fig. A)


WARNING: Never modify the power tool or any part of it. Damage or personal injury
could result.
1 On/off switch
Handle
2
Front guard
3
Lower guard
4
Fixed table top
5
6 Leg
Left fence (small)
7
Right fence (large)
8
2020 XX XX
9 Dust shroud
Mitre latch lever
10
Mitre clamp lever
11
Height adjustment crank
12
Radial arm
13
14 End‑cap
cable
15
Dust outlet
16
Yoke assembly
17
18 Motor
Left table strip
19
Right table strip
20
Left table extension
21
Intended Use
The radial arm saw has been designed for professional woodworking. This high precision
machine can be easily and quickly set to crosscut, bevel, mitre. For optimum safety, all major
controls have both a latch and a locking device. Also refer to the quick reference chart at the
end of the section. This saw is designed for use with a 350 mm diameter carbide tip blade.
DO NOT use under wet conditions or in the presence of flammable liquids or gases.
The radial arm saw is a professional power tool.
DO NOT let children come into contact with the tool. Supervision is required when
inexperienced operators use this tool.
• Young children and the infirm. This appliance is not intended for use by young children
or infirm persons without supervision.
• This product is not intended for use by persons (including children) suffering from
diminished physical, sensory or mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their safety. Children should never
be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal injury, turn tool off and
disconnect tool from power source before making any adjustments or removing/
installing attachments or accessories. Be sure the trigger switch is in the OFF position.
An accidental start-up can cause injury.

WARNING: For optimum performance of your saw, it is of vital importance to follow the
procedures in the paragraphs below.
Set Up
Mounting the Height Adjustment Crank (Fig. A, B, C)
1. Rotate the arm to the central position.
2. Press the mitre latch lever 10 down as shown (Fig. B).
3. Tighten the mitre clamp lever .
11
4. Introduce the height adjustment crank
engages in the nut inside the column.
5. Turn the height adjustment crank clockwise until it is fully seated (Fig. C).
6. Align the mitre scale 53 with the pointer
height adjustment crank with 6 mm hex wrench.
7. Raise the height adjustment crank high enough to provide clearance for removal of various
elements under the motor.
Assembling the Legstand (Fig. A, D)
The legstand components and fasteners are packed separately.
1. Remove all parts from the package.
2. Lock the arm using the mitre clamp lever
3. Tilt the machine carefully from the pallet until the rear of the column is resting on the floor.
4. Place a piece of wood 28 under the edge of the table (Fig. D).
5. Assemble the legs 6 as shown using the nuts, bolts and flat washers provided.
6. Firmly tighten all fasteners.
7. Tilt the machine to upright position.
IMPORTaNT: Assistance may be required to lower and raise the machine.
Anchor the Machine (Fig. A, E)

WARNING: The machine must be level and stable at all times.
1. Move the machine to the desired location. See Transporting paragraph
under Maintenance.
2. Holes 40 in the legstands are provided to secure the machine to the floor. Using these
holes as templates, drill 10 mm diameter holes with a minimum depth of 75 mm.
3. Insert the anchor bolts 59 , with washer
in legs and into the floor. NOTE: Use FAZ ll 10/10 anchor bolts, sold separately.
4. Tighten nut 61 .
Mounting the Table Extension (Fig. A, F–M)
Figure F shows the correct position of the triangular supports. The supports are mounted using
M8 x 20 bolts and corresponding nuts and with D8 flat washers at the front, but not at the rear.
1. Mount the triangular supports 29 with the flat side of the support facing the operator.
2. Mount the straight supports 30 to the flat side of the triangular support
3. Fit the two table extensions 21 , 22
(Fig. G).
4. Firmly tighten all fasteners.
5. Check that the table extensions are flush with the fixed table top and securely hand
tighten the bolts.

WARNING: The table extensions and the fixed table top MUST be flush.
6. Insert 3 dowels into the small, left fence
(Fig. H).
Right table extension
22
23 Bevel scale
Roller head assembly
24
Isolating switch
25
Switch box
26
12 into the column 27 as shown until the crank
52 and tighten the three screws 31
11 .
60 and nut 61 partially threaded, through holes
29
to the supports with M8 x 25 bolt, washer and nut
and 3 dowels into the larger right fence
7
ENGLIsh
inside the
.
8
25