Package Contents - DeWalt D24000 Originalanweisungen


WARNING: Never use a light socket.
Never connect the live (L) or neutral (N) wires to the earth pin marked E or
Fitting a Mains Plug to 115 V Units
(U.K. and Ireland Only)
• The plug should be fitted by a competent person. If you are in doubt, contact an authorized
D WALT repair agent or a qualified electrician.
e
• The plug fitted should be comply with BS EN 60309 (BS4343), 16 Amps, earthing contact
position 4h.
Using an Extension Cable
If an extension cable is required, use an approved 3–core extension cable suitable for the
power input of this tool (see technical data). The minimum conductor size is 1.5 mm
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.
Portable Residual Current Device
The machine is equipped with a portable residual current device (PRCD), which protects the
user against electric shock by interrupting the circuit when a leakage current of 10 mA or
greater is detected.
WARNING: Never operate the machine without the PRCD in place. Do not use the
machine if the PRCD does not function properly. For the PRCD to work, the machine
must be connected to an earthed wall socket. Before using the tile saw, check the
function of the PRCD, pressing the TEST button.

Package Contents

This package continas:
1 Motor frame assembly
1 Support frame assembly
1 Water basin
1 Water pump
1 Cutting disc
1 Sliding table
1 Extension table
1 Edge guide
1 Rear water collector
1 Sliding table water collector
4 Hex screws
1 Hex key
1 Instruction manual
• Check for damage to the tool, parts or accessories which may have occurred during transport.
• Take the time to thoroughly read and understand this manual prior to operation.
Labels on tool
The following pictographs are shown on the tool.
Read the instruction manual before use.
Do not use recessed cutting discs.
Wear safety goggles.
Always wear regular working gloves while operating this tool.
Always wear ear protection.
WaRnInG! Sharp edges.
.
2 ; the
25.4mm
Date Code (FIg. B1)
The date code 72 . which also includes the year of manufacture, is printed into the nameplate.
Example:
Description (Fig. A1, A2)

WARNING: Never modify the power tool or any part of it. Damage or personal injury
could result.
1 On/off switch
Depth adjustment knob
2
3 Operating handle
Sliding table
4
5 Edge guide
Extension table
6
Water nozzles
7
8 Cutting disc
Guard
9
10 Water basin
Depth stop
11
Bevel adjustment knob
12
Key storage
13
Sliding table water collector
14
15 Rear water collector
Intended Use
Your D24000 tile saw has been designed for professional wet tile cutting applications. Using
the appropriate cutting disk, diameter 250 mm, it can cut concrete, brick, porcelain and
ceramic materials. Providing optimum versatility, the machine performs the cutting operations
of straight cutting (ripping), diagonal cutting, plunge cutting and bevel cutting easily,
accurately and safely.
This machine is not to be used for any operation other than those mentioned in this manual.
DO nOt use under wet conditions or in the presence of flammable liquids or gases.
DO nOt let children come into contact with the tool. Supervision is required when
inexperienced operators use this tool.
Young children and the infirm. This appliance is not intended for use by young children
•
or infirm persons without supervision.
• This product is not intended for use by persons (including children) suffering from
diminished physical, sensory or mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their safety. Children should never
be left alone with this product.
ASSEMBLY

WARNING: Prior to assembly always unplug the tool.

WARNING: When assembling the machine, always follow the instructions in the order as
described below.
Unpacking the Machine and Its Parts

WARNING: When moving the machine, always seek assistance. The machine is too
heavy for one person to handle.
1. Remove the loose packaging material from the box.
2. Lift the machine parts out of the box.
3. Remove any remaining packing material from the machine parts.
Mounting the Motor Frame to the Support Frame (Fig. B1)
1. Place the support frame
2. Place the motor frame
the mounting holes
3. Insert a screw 20
4. Tighten the screws using the hex key
On/off switch: position I (on) and 0 (off ).
Carrying point
Do not place your hands within this area.
Max. depth of cut.
Bore diameter
2020 XX XX
Year of Manufacture
16 on a relatively smooth and level surface.
17 on the support frame aligning the holes in the foot
19 .
into the holes.
21 provided.
EnGLIsh
18 with
31