Operation - XQ MAX 8EH-000010 Gebrauchsanweisung

When the spa is properly inflated, press the "Jet"
button to shut off the bubbles.
Attention 1: Do not over inflate.
Attention 2: If you want inflation when the spa is
filled with water, you must put on the Jets 2-3 minutes
by pressing the "Jet" button first, and then operate
according to step 2-5 above.
5. Remove the inflation hose and screw the valve tight.
6. Remove the inflation hose from the air outlet and
screw the nut tight.
7. Screw the filter cartridge onto the water inlet on the
spa wall by turning it clockwise.
8. Fill the spa using a garden hose to fill to the water level
printed on the spa wall.
9. Place the cover onto the spa, fasten the zipper.

OPERATION

A. You must ensure the water in the spa matches the
water line printed on the spa wall.
B. Control panel.
FILTER KEY
On-off key for the filtration system. Press this key, and the
filter pump will start working and the red indicator lamp
will be on. Press again and the pump will stop working
and the lamp will be off. When the FILTER PUMP has
worked for 168 hours, the letters 'FC' will appear on the
display screen, accompanied by a warning tone. At that
time, the indicator lamp for the key of filtration system
will be on but the filter pump will actually not work.
The indicator lamp for the key of the heating system
will be off and the heating system will not work. Only by
pressing the key 'FILTER' again can the indicator lamp for
the key of the filtration system be off. At that time, the
letters 'FC' on the display screen will disappear and so will
the warning tone. The actual water temperature will be
displayed. All keys return to normal working status. 'FC'
and the warning tone are to remind the user to clean or
replace the filter element.
JET KEY
On-off key for the jet system. Press this key and the air
pump will start working and the red indicator lamp will be
on. Press again and the jet system will stop working and
the lamp will be off. The jet system will stop automatically
after working for 20 minutes. If there is still need, you have
to wait for 10 minutes and then press the "Jet" key again.
During the time period when the bubbling function has
been started and has worked for 15 minutes, bubbling can
be stopped or started. During the time period that the jets
have been working for 15 minutes and stopped, bubbling
4 | Instructions for use – Inflatable jacuzzi
can be stopped but not be started. The re-starting of jets
should wait for 10 minutes. When the jets have been
on for 20 minutes and stopped, the function cannot be
started again within 10 minutes.
HEATER KEY
On-off key for the heating system. Press this key the heating
system will start working and the red indicator lamp will be
on. Press again and the heating system will stop working and
the lamp will be off. When pressing down the key 'HEATER' ,
the heating system will start working and the red indicator
lamp will be on. At the same time, the red indicator lamp of
the key FILTER will also be on and the filter pump will start
working too. This is a normal phenomenon required by the
design. When the preset temperature has been reached, the
heating system will stop working while the heating indicator
lamp will not turn off. The filter pump will stop working and
the filtration indicator lamp will be off. When the water
temperature falls to 2 degrees below the preset temperature,
the heating system will start working automatically and so
will the filter pump. The filtration indicator lamp will be on.
TEMPERATURE KEY
Key for setting temperature. Press this key and the
numbers on the display screen will start flashing, and
the keys for increasing or decreasing temperatures can
be pressed to set the temperature. When settings are
finished, press the TEMPERATURE Key again to confirm.
Default temperature is 40°C, and temperature can be set
in the range of 20-42°C.
Key for increasing temperature
Key for decreasing temperature
Base of the controller is made of environmental-friendly
PU material that is soft and comfortable. Surface of the
base can be washed. The controller is chrome-plated,
which meets ROHS standards. Surface films are glued to
the controller by marine glue.
1. BODY OF SPA:
1.1. Air inflation of water tank body: air pressure for air
inflation of water tank body is indicated by the green
area of the pressure gauge. If air pressure does not
reach the green area, air inflation can continue until
reaching the green area. If air pressure goes beyond
the green area, please stop the air inflation.
1.2. Water filling of water tank body: water should be
filled to a position 20mm higher than the water line.
If lower, heating may not be realized. If higher, water
may spill over the tank in use.
2. MAINTENANCE OF WATER IN THE WATER TANK
BODY
2.1 Water in the water tank body should be filtered at
fixed time regularly. It is not suggested to filter the
water at all times.
2.2 Water in the water tank body should be treated with
chemical agents periodically. However, chemical
agents with calcium ions must not be used. If
chemical agents with calcium ions are used for water
treatment, there will be very likely to form scales on
the walls of the water tank and inner heating pipes.
Water scales will directly damage the inner electrical
components inside the control cabinet and further
affect the service life of the control cabinet.
2.3 If the filtration system has worked for 168 hours, the
system will emit a warning tone to remind the user
to clean or replace the filter element.
3. CONSERVATION OF SPA
- Drain off the water inside the water tank completely and
wipe off droplets of water on the walls. After that, lay
aside the SPA for 24 hours, exhaust the air and fold. All
components should be completely dry before storage.
- Use a sponge with a mild detergent to remove residual
dirt or stains. Note: do not use steel wool, hard brushes
or abrasive cleaners.
- Fold up the SPA loosely without sharp edges to prevent
damage or leaks.
- If it is winter, please fold the SPA indoors. Because
outside temperature in winter is very low and materials
may become hard. In that case, folding the materials
may result in breakage. Store the SPA between 0°C
(32°F ) and 40°C (104°F)
- Put the SPA inside the packing case after folding it well and
then put the case in a shaded place to avoid direct sunlight.
- Ensure you have enough clean filters available for the
next use of the SPA.
4. MAINTAINING
MAINTAINING WATER
Protect spa users against diseases causes by water.
Always ensure the correct hygiene and maintain the
water properly. To ensure that the water is of good quality
you can follow the instructions below:
4.1. Clean your filter cartridge at least once a time after
it worked continuously for 72-120 hours. The filter
cartridge should be replaced at least once a month
depending on use.
4.2. Change water every few days or use appropriate pool
chemicals. All spas require the use of pool chemicals.
Please consult your local pool supply retailer for more
information about chemical maintenance. Pay close
attention to the chemical manufacturer's instructions.
4.3. Water balance; we recommend maintain your water
PH between 7.2 and 7.8, total alkalinity between 80
and 120ppm and free chlorine between 3 to 5ppm.
Purchase a test kit to test your water chemistry
before each use of the spa, no less than once per
week. Low PH will damage to the spa and pump.
4.4. Water sanitation is the responsibility of the spa owner,
achieved through the regular and periodic (daily, if
necessary) addition of an approved sanitizer. The sanitizer
will chemically control bacteria and viruses present in the
fill water or introduced during use of the spa.
5. CLEANING THE FILTER CARTRIDGE
5.1. Make sure to unplug the power pack from the
electrical receptacle before the following actions.
5.2. Unscrew the filter cartridge by turning
counterclockwise.