Operation; Programs; Saving Programs; Locking Programs - Omnitronic DXO-26 PRO Bedienungsanleitung

OPERATION

Switch the device on via the power-switch.

Programs

Saving programs

You can save up to 60 programs. Press the SAVE/ENTER-button for saving. The display shows the last
used program. Press the PREV/NEXT-button for adjusting program 1-60. With these buttons, you can also
rename the program. In order to move the cursor (e.g. for entering the next letter or correcting the last letter),
press the < / >-buttons.
Confirm your entry by pressing the SAVE/ENTER-button.
The little star in the right, upper corner indicates that the current program has not been saved since the last
modification.

Locking programs

In order to avoid easy overwriting, you can lock a program. After saving, you can choose Locked or
Unlocked. Choose your selection with the jog-wheel or with the >-button and press the SAVE/ENTER-button
to confirm.
If you want to save a new program on a locked one, the display shows Program locked. After this message
has disappeared, you can unlock the program with the Next-button or with the jog-wheel.

Calling up programs

You can call a program up via the Recall-button. Select the desired program via the Prev/Next-button or the
jog-wheel. You can only select from already saved programs.
Press the Recall-button another time in order to call up the desired program.

Setup-menu

Press the Prev/Next-buttons in order to navigate in the setup-menu. Make your adjustments via the <>-
button or the jog-wheel. Press the Recall-button in order to leave a mode.

Stereo-link

The stereo-link links two outputs with each other depending on the selected operation mode. In the 2-way
mode, the outputs 1 and 3, 4 and 6 and 2 and 5 are linked. In the 3-way mode, the outputs 1 and 2, 3 and 4
and 5 and 6 are linked.
The kind of link is either step or offset differing from parameter to parameter. A step-link is a fixed link
between two channels, i.e. if a parameter value is changed, the same parameter of the other channel
automatically changes to the same value.
An offset-link is a relative link between the channels, i.e. if a parameter value is changed, the same
parameter of the other channel automatically receives the relative value.
Overview on the link:
Parameter
Input Delay
Input EQ Type
Input EQ Frequency
Input EQ +/-
Output Name
Output Source
Output Gain
Output Limit
Output Delay
Output Delay Link
Output Polarity
Output Lo Shape
Output Lo Frequency
Output Hi Shape
Link 3-way-mode
Offset A-B
Step A-B
Offset A-B A-B
Offset A-B
Offset 1-2, 3-4, 5-6
Offset A(1, 3&5) / B(2, 4&6)
Offset 1-2, 3-4, 5-6
Offset 1-2, 3-4, 5-6
Offset 1-3, 3-5, 2-4, 4-6
Offset 1-3, 3-5, 2-4, 4-6
Step 1-2, 3-4, 5-6
Step 1-2, 3-4, 5-6
Offset 1-2, 3-4, 5-6
Step 1-2, 3-4, 5-6
2-way-mode
A-B
A-B
A-B
1-3, 4-6
A(1&4) / B(2&6) / A+B(3&5)
1-3, 4-6
1-3, 4-6
1-4, 2-5, 3-6
1-4, 2-5, 3-6
1-3, 4-6
1-3, 4-6
1-3, 4-6
1-3, 4-6
25/33 10356350_V_1_1.DOC