Fuel Recommendations; Maintenance - Briggs & Stratton Quantum Snow 120000 Betriebsanleitung & Wartungsvorschriften

FUEL RECOMMENDATIONS

Use clean, fresh, lead-free, regular gasoline with a minimum of
85 octane. Leaded gasoline may be used if it is commercially
available and if unleaded is unavailable. Purchase fuel in
quantity that can be used within 30 days. See storage
instructions.
In U.S.A. leaded gasoline may not be used. Some fuels, called
oxygenated or reformulated gasolines, are gasolines blended
with alcohols or ethers. Excessive amounts of these blends
can damage the fuel system or cause performance problems.
If any undesirable operating symptoms occur, use gasoline
with a lower percentage of alcohol or ether.
This engine is certified to operate on gasoline. Exhaust
Emission Control System: EM (Engine Modifications).
Do not use gasoline which contains Methanol. Do not mix oil
with gasoline.
For engine protection, we recommend using Briggs & Stratton
Fuel Stabilizer available from an Authorized Briggs & Stratton
Service Dealer.
ADDING FUEL
Fig. 4
WARNING
Before refueling, allow
engine to cool 2 minutes.
Clean around fuel fill before removing cap to refuel. Remove
cap. Fill tank to approximately 1-1/2 inches below top of neck
to allow for fuel expansion. Be careful not to overfill.
STARTING
Fig. 5
WARNING
1. Add oil. Ensure level is at FULL mark on dipstick. Use
the correct oil type for expected starting temperature.
DO NOT OVERFILL.
2. Fill with fresh gasoline.
Ê
3. Push stop switch to ON position.
Ë
Move CHOKE to choke position.
Locate primer bulb. Firmly press with finger
Note: If temperature is 15° F (−9° C) or higher push
primer two times, if below 15° F (−9° C) push primer
four times.
Í
4. Grasp rope handle. Pull slowly until resistance is felt,
then pull rapidly to start engine and avoid kickback.
OPERATING ENGINE
After engine has started, let it warm up several seconds to
several minutes, depending on outside temperature. Slowly
adjust CHOKE to RUN position. Wait until the engine runs
smoothly before each choke adjustment.
• Do not tip engine or equipment at angle which causes
gasoline to spill.
• Do not choke carburetor to stop engine.
Periodically remove debris buildup under housing.
(See Maintenance.)
STOPPING
Fig. 6
CAUTION: Do not move choke control to CHOKE
position to stop engine. Backfire or engine damage may
occur. KEEP CHOKE IN RUN POSITION.
1. Push stop switch to OFF position.
2. To prevent rewind freeze up from melted snow after the
engine is shut-off, pull the rope handle until resistance is
felt, then stop. Repeat three times.

MAINTENANCE

To prevent accidental starting, remove spark
plug wire and ground it before servicing.
We recommend that you see an authorized Briggs & Stratton
Dealer for all maintenance and service. Use only Briggs &
Stratton parts.
Emission Control
Maintenance, replacement or repair of the emission
control devices and systems may be performed by any
nonroad engine repair establishment or individual. How-
ever, to obtain no charge repairs under the terms and
provisions of the Briggs & Stratton warranty statement, any
service or emission control part repair or replacement must be
performed by a factory authorized dealer. See Emission
Warranty.
WARNING
done, the flywheel may shatter during operation.
Do not tamper with governor spring, links or other parts to
increase engine speed.
Follow the hourly or calendar intervals, whichever occur
first. More frequent service is required when operating in
adverse conditions noted below.
First 5 Hours
.Ì
D Change oil.
Every 8 hours or daily
D Check oil level.
D Clean debris.
Every 50 hours or every season
D Change oil.
Every 100 hours or every season
D Clean/replace spark plug.*
D Clean the air cooling system.
Every 100-300 hours
D Clean combustion chamber.
*
In some areas, local law requires using a resistor
spark plug to suppress ignition signals. If this engine
was originally equipped with resistor spark plug, use
same type of spark plug for replacement.
Ê
Ë
WARNING
Do not strike the flywheel with
hammer or hard object. If
3
CHANGING ENGINE OIL
Fig. 7
WARNING
DRAIN
PIPE
PLUGS
Change oil after first 5 to 8 hours of use, then every 50 hours
or every season. Change oil every 25 hours when operating
the engine under heavy load or in high temperatures. Engine is
equipped with either top or bottom oil drain.
1. Run engine until it runs out of fuel. Otherwise, fuel can
leak out, creating a fire/explosion hazard, when you tip
engine in Step 4 for top oil drain.
2. Disconnect spark plug wire and keep it away from spark
plug.
3. With engine OFF but still warm drain oil.
4. On top oil drain: Remove dipstick and turn engine to
drain oil, keep spark plug side up.
Ë
appropriate receptacle.
5. On bottom oil drain: Remove drain plug and drain oil
Ë
into appropriate receptacle. Reinstall drain plug.
CAUTION: Used oil is a hazardous waste product.
Dispose of used oil properly. Do not discard with
household waste. Check with your local authorities,
service center, or dealer for safe disposal/recycling
facilities.
6. Place engine level. Add about 0.5 liter (18 ounces) new
oil. Fill to FULL line on dipstick. Do not overfill. Replace
dipstick. Check every 8 hours or daily, before starting
engine.
AIR COOLING SYSTEM
Fig. 8
Dirt and debris may clog engine's air cooling system,
especially after prolonged service. Internal cooling fins and
surfaces may require cleaning to prevent overheating and
engine damage.
Ê
1. Remove 3 screws from housing
Í
2. Clean areas shown, Clean around rewind starter
Ì
housing.
3. Reinstall housing ensuring all hoses, and wires are in
place.
SPARK PLUG SERVICE
Check the spark plug every season. Replace the spark plug if
upon inspection the electrodes are burned or worn. Ensure the
Ê
spark plug is clean. Check the gap with a feeler gage and
reset to .76 mm or .030 in. if necessary. Use only Briggs &
Stratton Spark Tester (part number 19368) to check for spark.
Ê
3/8"
SQUARE
Ê
Drain oil into
Ë
and lift.