Steam Distribution; Drawing Hot Water; Turning Off The Machine; Programming Doses (De Version) - Bezzera BZ07 DE Bedienungsanleitung

2) Load the filter holder with ground coffee, press
the coffee down taking care to not dirty the edge
of the filter holder.
3) Reattach the filter holder in its housing.
PM VERSION
4) Start up coffee distribution by pressing the
distribution button (Fig. 04; pos. a).
5) Stop distribution when the desired quantity is
reached, by pressing the distribution button
again.
DE VERSION
4) Use the coffee distribution keypad (Fig. 05),
by pressing one of the keys, depending on the
desired dose.
To change dose programming, follow the
instructions in paragraph 5.7 of this booklet.
The machine is set for continuous distribution: press
the key " " (Fig. 05; pos. c) to start up distribution,
press again to stop..
Warnings:
- Do not remove the filter holder full of coffee when
the machine is working, as it is pressurised.
- Do not touch the metal part of the filter holder
directly as it is hot.

5.4 Steam distribution

1) To avoid liquids being sucked into the boiler,
discharge the steam by turning the tap knob
(Fig. 01; pos. 9).
2) Insert the steam nozzle (Fig. 01; pos. 10) in the
container of the liquid to be heated.
3) Press down and hold the steam tap knob (Fig.
01; pos. 9). The amount of steam distributed
is proportional to the opening of the tap; the
more the tap is opened, the more steam will be
distributed.
4) Once steam has been distributed, release knob,
remove liquid container and clean the steam
nozzle immediately with a damp cloth to remove
heated liquid residues.
Warning: Do not touch the steam nozzle directly
as it is hot.

5.5 Drawing hot water

1) Place the water container under the nozzle (Fig.
01; pos. 8).
2) Press down and hold the water tap knob (Fig. 01;
pos. 7) to draw the amount of water required.
Downloaded from CoffeeMachineManual.com Manuals
Downloaded from www.Manualslib.com
(Fig. 06)
manuals search engine
3) Once water has been distributed, release the
knob.
Warning: Do not touch the water distributor tap
directly as it is hot.

5.6 Turning off the machine

1) Turn the main switch (Fig. 01; pos. 1) to position
"0" and check that the green light has turned
off. (Fig. 01; pos. 2)
2) Close the water interception tap (R version).
5.7 Programming doses
(Fig.05)
a = single dose
b = double dose
c = continuous/programming distribution
To programme each single dose, proceed as
follows: keep the programming key pressed down
for about 5 seconds " " (Fig. 05; pos. c) until the
LED light flashes.
Select the desired dose by pressing the
corresponding key (a-b) (LED turns on); press the
key again one the desired dose has been reached
(LED turns off): the dose has in this way been
programmed.
Notes:
- The LED lights on the keypad flash intermittently:
low water level in tank.
- The LED lights on the keypad flash rapidly: low
water level in boiler.
- The LED light of the selected button flashes:
coffee ground too finely.
N.B.
If no water comes out from the distribution unit (Fig.
01; pos. 5) even if the boiler is pressurised and the
tank is at a working level, some air bubbles may
have formed in the circuit that stop the pump from
working normally or the aspiration pipe may not
have been correctly inserted in the tank.
To restore working order if air bubbles have formed,
proceed as follows:
1) Turn the main switch off (Fig. 01; pos. 1) and
discharge steam from the tap (Fig.01; pos. 9).
Wait for the machine to cool down completely.
PM VERSION
2a) Turn the main switch on again (Fig. 01; pos.
1) and press the distribution button (Fig. 04;
pos. a) until the water comes out of the unit;
press the button again (Fig. 04; pos. a) and
wait for the machine to become pressurised.
DE VERSION
25
MOD. BEZZERA BZ07
(DE VERSION)