Hilti TE 80-ATC Bedienungsanleitung Seite 21

Power tool
Rated current input
en
Mains frequency
Hammer drilling speed
Single impact energy in accordance
with EPTA procedure 05/2009 (full
power setting)
Single impact energy in accordance
with EPTA procedure 05/2009 (50%
power setting (optional))
NOTE
This equipment complies with the applicable standard provided that the maximum permissible mains supply impedance
(Zmax) at the point where the user's installation is connected to the public supply network is less than or equal to
0.315+j0.197 Ω. It is the responsibility of the installer or user of the equipment to ensure, by consultation with the
supply network operator if necessary, that the equipment is connected only at a point in the supply with an impedance
of less than or equal to Zmax.
Other information about the power tool
ATC electronic cut-out
Protection class
NOTE
The vibration emission level given in this information sheet has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment
of exposure. The declared vibration emission level represents the main applications of the tool. However if the tool is
used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total working period. An estimation of the level of exposure to
vibration should also take into account the times when the tool is switched off or when it is running but not actually
doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety
measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
Noise and vibration information (measured in accordance with EN 60745):
Typical A-weighted sound power level, TE 80-ATC
Typical A-weighted emission sound pressure level, TE
80-ATC
Typical A-weighted sound power level for the
TE 70‑ATC/ TE 70/ TE 70B
Typical A-weighted emission sound pressure level for
the TE 70‑ATC/ TE 70/ TE 70B
Uncertainty for the given sound level
Triaxial vibration value for the TE 80-ATC (vibration vec-
tor sum)
Hammer drilling in concrete, a
Chiseling, a
h, Cheq
Triaxial vibration value for the TE 70-ATC (vibration vec-
tor sum)
Hammer drilling in concrete, a
18
Downloaded from www.Manualslib.com
TE 80‑ATC
Rated voltage 100 V: 15 A
Rated voltage 110 V: 16 A
Rated voltage 120 V: 15 A
Rated voltage 220 V: 9.8 A
Rated voltage 230 V: 9.9 A
Rated voltage 240 V: 10 A
50...60 Hz
380/min
11.5 J
5 J
h, HD
h, HD
manuals search engine
TE 70‑ATC/ TE 70/ TE 70B
Rated voltage 100 V: 15 A
Rated voltage 110 V: 16 A
Rated voltage 120: 15 A
Rated voltage 127 V, only TE 70:
15 A
Rated voltage 220 V: 9.6 A
Rated voltage 230 V: 9.8 A
Rated voltage 240 V: 9.8 A
50...60 Hz
360/min
11 J
5 J
TE 80‑ATC/ TE 70‑ATC
Protection class II (double insulated)
110.5 dB (A)
99.5 dB (A)
110.5 dB (A)
99.5 dB (A)
3 dB (A)
Measured in accordance with EN 60745‑2‑6
8.8 m/s²
8.5 m/s²
Measured in accordance with EN 60745‑2‑6
22 m/s²