Proper Use; Technical Data; Before Starting The Equipment - EINHELL GE-HH 18/45 Li T Originalbetriebsanleitung

•
Battery pack (not included in delivery with
Art. No. 34.108.66)
•
Charging unit (not included in delivery with
Art. No. 34.108.66)
•
Original operating instructions
•
Safety instructions

3. Proper use

Hedge trimmer
The hedge trimmer mounting kit is allowed to be
used only on the supplied motor head.
Caution! This hedge trimmer is suitable for cut-
ting hedges, bushes and shrubs. Caution! Do not
use this equipment to cut grass.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

Cutter bar length: ................................... 450 mm
Max. cutting length: ................................ 400 mm
Tooth spacing: .......................................... 16 mm
Cuts/min: ..................................................... 1700
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with ISO 22868.
L sound pressure level ................... 81.05 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level measured .... 98.23 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
L sound power level guaranteed ..... 102 dB(A)
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with ISO 22867.
Anl_GE_HH_18_45_Li_T_SPK13.indb 19 Anl_GE_HH_18_45_Li_T_SPK13.indb 19
GB
Handle under load
Vibration emission value a
The quoted total vibration value and the quoted
noise emission values were measured in ac-
cordance with standardized test procedures and
can be used to compare one electric tool with
another. They can also be used for a provisional
assessment of the level of exposure.
Warning!
The vibration and noise emission levels during
actual use may vary from the values quoted,
depending on the way in which the electric tool is
used and, in particular, on the type of workpiece
being processed.
For the operator's protection it is essential to spe-
cify safety measures based on an estimate of the
exposure to vibrations during the actual condi-
tions of use (all stages of the operating cycle must
be considered in this connection, e.g. times in
which the electric tool is OFF and times in which
the tool is ON but operating without load).
Try to keep the exposure to vibrations and noise
as low as possible. Examples of measures for
reducing the exposure to vibrations include the
wearing of gloves when using the tool, the limiting
of work time and the use of accessories that are
in good condition.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.

5. Before starting the equipment

Caution! Do not fi t the battery until the equipment
has been fully assembled and all the settings
have been actuated. Always wear protective
gloves when working on the equipment to protect
yourself against injury. Carefully unpack all parts
and check that they are complete (Fig. 1).
- 19 -
≤ 2.5 m/s
2
h
01.12.2021 10:53:52 01.12.2021 10:53:52