Black+Decker BDCDD12 Übersetzung Der Originalanleitung Seite 7

Features
This tool includes some or all of the following
features.
1. Variable speedswitch
2. Forward/reverse slider
3. Torque adjustment collar
4. Keyless chuck
5. Battery
6. Battery release button
7. Charger
Assembly
Use
Warning! Let the tool work at its own pace. Do
not overload.
Charging the battery (fi g. A)
The battery needs to be charged before fi rst use
and whenever it fails to produce suffi cient power
on jobs that were easily done before. The battery
may become warm while charging; this is normal
and does not indicate a problem.
Warning! Do not charge the battery at ambient
temperatures below 10 °C or above 40 °C.
Recommended charging temperature: approx.
24 °C.
Note: The charger will not charge a battery if
the cell temperature is below approximately
10 °C or above 40 °C. The battery should
be left in the charger and the charger will
begin to charge automatically when the cell
temperature warms up or cools down.
♦ Plug the charger (8) into any standard
230 Volts 50 Hz electrical outlet.
♦ Slide the battery pack into the charger as
shown in fi gure A.
♦ The green LED (9) will fl ash indicating that the
battery is being charged.
♦ The completion of charge is indicated by the
green LED remaining on continuously. The
pack is fully charged and may be used at this
time or left on the charger.
Warning! Do not use tool while it is connected to
the charger.
Warning! Fire hazard. When disconnecting
the charger from the tool, be sure to unplug the
charger from the outlet fi rst, then disconnect the
charger cord from the tool.
Installing and removing the battery pack
from the tool (fi g. B)
Warning! Make certain the lock-off button is
engaged to prevent switch actuation before
Downloaded from www.Manualslib.com manuals search engine
removing or installing battery. To install battery
pack:
♦ Insert battery pack into tool, until an audible
click is heard (fi g. B)
Removing the battery pack from the tool
(fi g. C)
♦ Depress the battery release button as shown
in (fi g. C) and pull battery pack out of tool.
Operating Instructions
Trigger switch & reversing button (fi g. D)
♦ The drill is turned ON and OFF by pulling and
releasing the trigger switch (1). The farther the
trigger is depressed, the higher the speed of
the drill operates at
♦ A forward/reverse control button (2)
determines the direction of the tool and also
serves as a lock off button.
♦ To select forward rotation, release the trigger
switch and depress the forward/reverse
control button to the left.
♦ To select reverse, depress the forward/
reverse control button the opposite direction.
♦ To lock the tool, set the forward/reverse slider
into the centre position.
Note! The center position of the control button
locks the tool in the off position. When changing
the position of the control button, be sure the
trigger is released.
Torque control (fi g. E)
This tool is fi tted with a torque adjustment collar
(3) to select the operating mode and to set the
torque for tightening screws. Large screws and
hard workpiece materials require a higher torque
setting than small screws and soft workpiece
materials.
♦ For drilling, set the collar to the drilling position
symbol .
♦ For screwdriving, set the collar to the desired
setting. If you do not yet know the appropriate
setting, proceed as follows:
♦ Set the collar to the lowest torque setting.
♦ Tighten the fi rst screw.
♦ If the clutch ratchets before the desired
result is achieved, increase the collar
setting and continue tightening the screw.
Repeat until you reach the correct setting.
Use this setting for the remaining screws
Keyless chuck (fi g. F)
Warning! Make certain the lock-off button is
ENGLISH
7