EINHELL 43.405.15 Originalbetriebsanleitung Seite 30

2200 W Idling speed n .....................................
0
4250 rpm Carbide saw blade ..........Ø 254 x Ø
30 x 2.4 mm
Number of teeth ............................................... 48
Table size ......................................580 x 555
mm Table width extension left/right ......580 x
150 mm Table length extension, width
................. 555 mm Support surface max.
..................830 x 1055 mm Cutting height max.
........................... 80 mm / 90°
........................................................ 55 mm / 45°
Height adjustment .................... infi nite 0 - 80
mm Tilting saw blade .......................... infi nite 0°
- 45° Cross stop angle .......................infi nite -
45° - 45° Extractor connection
.............................Ø 36 mm Weight
........................................ approx. 26.5 kg
Protection class: ........................................... II/
Thickness of the splitter .......................... 2.0
mm
Operating mode S6 25%: Continuous operation
with idling (cycle time 10 minutes). To ensure
that the motor does not become excessively hot,
it may only be operated for 25% of the cycle at
the specifi ed rating and must then be allowed to
idle for 75% of the cycle.
Danger!
Noise
The noise emission values were measured in
accordance with EN 62841.
Operation
L sound pressure level ..................... 93.2
pA
dB(A) K uncertainty ........................................ 3
pA
dB(A) L sound power level .....................
WA
106.2 dB(A) K uncertainty
WA
........................................ 3 dB(A)
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
The stated noise emission values were
measured in accordance with a set of
standardized criteria and can be used to
compare one power tool with another.
The stated noise emission values can also be
used to make an initial assessment of exposure.
Warning:
The noise emission levels may vary from the
level specifi ed during actual use, depending on
the way in which the power tool is used,
especially the type of workpiece it is used for.
Anl_TC_TS_2225_U_SPK9.indb 30
GB
Keep the noise emissions and vibrations to a
minimum.
•
O nly use appliances which are in perfect
working order.
•
S ervice and clean the appliance regularly.
•
A dapt your working style to suit the
appliance.
•
D o not overload the appliance.
- 26 -
•
H ave the appliance serviced whenever
necessary.
•
S witch the appliance off when it is not in
use.
Limit the operating time! All stages of the
operating cycle must be considered (for example,
times in which the electric tools are switched off
and times in which the tool is switched on but
operates without load).
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain
residual risks cannot be rules out. The
following hazards may arise in connection
with the equipment's construction and
layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is used.
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating
plate are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
bench-type circular saw and check it for damage
which may have occurred in transit.
•
T he machine has to be set up where it can
stand firmly, e.g. on a work bench, or it must
be bolted to a strong base.
•
A ll covers and safety devices have to be
properly fitted before the machine is
switched on.
•
I t must be possible for the saw blade to run
freely.
•
W hen working with wood that has been
processed before, watch out for foreign
bodies such as nails or screws etc.
- 27 -
•
Unpack the
29.10.2019 11:29:10