Before Starting The Equipment; Montage; Operation - Scheppach DP16VLS Betriebsanleitung

8. Before starting the equipment

• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport dam-
age.
• If possible, store the packaging until the warranty period
has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!

9. Montage

Column and machine foot, Fig. 3
1. Set the machine foot (1) down on the ground or the work-
bench.
2. Place the column (2) on the base plate so that the holes
on the column (2) align with the holes on the base plate
(1).
3. Screw the hexagonal screws (A) to fasten the column into
the base plate and tighten them using a hexagon span-
ner.
Table and pillar, Fig. 4
1. Slide the drilling table (3) onto the pillar (2). Position the
table directly above the base plate.
2. Install the table bolting (E) in the table unit from the left
side and tighten it.
Machine head and pillar, Fig. 5
1. Place the machine head (4) onto the pillar (2).
2. Put the spindle of the drilling machine with the table and
the base plate in the cover and fasten the 2 Allen screws
(F).
Drill chuck protection with depth stop, Fig. 6
1. Fit the chuck guard (7) on the spindle tube and tighten
the Philips screw (H).
2. Unfold the chuck guard (7).
3. Remove the nut (G) from the depth stop rod (8).
4. Guide the depth stop rod through the hole (I) on the ma-
chine head (4)
5. Fasten the depth stop rod (8) with the nut (G) in the hole
of the chuck guard (7).
6. Turn the pointer on the depth stop rod (8) to the scale on
the machine head (4).
The nuts (J) act to limit the depth.
Feed handles to the shaft hub, Fig. 7
1. Screw the feed handles (6) tightly into the threaded holes
in the hub.
Installing the chuck, Fig. 8
1. Clean the conical hole in the chuck (5) and the spindle
cone with a clean piece of fabric. Make sure there are
no foreign particles sticking to the surfaces. The slightest
piece of dirt on any of these surfaces will prevent the
chuck from seating properly. This will cause the drill bit to
wobble". If tapered hole in the chuck is extremely dirty,
use a cleaning solvent on the clean cloth.
2. Push the chuck up on the spindle nose as far as it wiII go.
3. Turn chuck sleeve clockwise (when viewed from above)
and open jaws in chuck completely.
4. Place a piece of wood on the machine table and lower
the spindle onto the piece of wood. Press firmly to ensure
that the food sits exactly.
Installing laser module (Fig. 15 and 16)
Fasten the laser module (13) with the countersunk screw (U)
onto the machine head (4) as shown in the figures.
Make sure the plastic pin on the laser module sits in the hole
without thread.
Fastening radial drill press to supporting surface
For your own safety, screw connection on a workbench or simi-
lar is strongly recommended.
Warning:
All the necessary adjustments for the good working of your drill
press have been done at the factory. Please do not modify them.
However, because of a normal wear and tear of your tool,
some readjustments might be necessary .

10. Operation

Warning:
If you are not familiar with this kind of machine, take advice
from an experimented person. In any case you should have
read and understood the safety and operational instruction be-
fore attempting to operate this product.
Pivoting the table, Fig. 10
1. To bring the table (3) to the inclined position, release the
table locking (S) and adjust the desired table angle.
2. Re-tighten the table locking.
Adjusting table height., Fig. 11
1. Loosen the table support lock handle (E).
2. Adjust the table (3) to the desired height.
3. Re-tighten the table locking (E).
Note: It is better to lock the table to the column in a position
so that the tip of the drill bit is just slightly above the top of the
workpiece
Choosing speed and tensioning belt, Fig. 12
Note! Pull power plug!
You can set different spindle speeds on your pillar drilling ma-
chine:
1. Once you have switched off the device, you can open the
belt guard (11). Loosen the screw (V) and open the belt
guard (11). All adjustment options for the spindle speed
are available in the machine's belt guard (11)
GB 21