Werbung
Verfügbare Sprachen
Verfügbare Sprachen
®
HD-SDI Surveillance Camera
GB
Please read these operating instructions carefully prior to
installation and keep them for later use.
1 Applications
This high-resolution colour camera is especially designed
for use in video surveillance systems (CCTV). It is
equipped with a lens with variable focus (6 – 50 mm).
Camera features include automatic day/night switching
with infrared suppression filter, backlight compensation,
digital noise reduction, mirror-inverted image display,
zoom, motion detection and a masking function to cover
zones that are not to be monitored. Due to its weather-
proof housing (IP 66), the camera is also suited for out-
door applications. The camera is equipped with a digital
output (SDI) for high-resolution image signals (HD) and
with an analog output for testing purposes. During dark-
ness, the 30 infrared LEDs illuminate up to 70 m of the
surveillance area.
2 Safety Notes
The camera corresponds to all relevant directives of the
EU and is therefore marked with
.
G
The camera housing is weatherproof, but not ab-
solutely watertight. Therefore, do not immerge the cam-
era into water.
G
Protect the camera against extreme temperatures (ad-
missible ambient temperature range: -10 °C to +50 °C).
G
Never touch the lens with your fingers. For cleaning the
lens, only use optical lens cleaners.
G
For cleaning the housing, never use aggressive deter-
gents or chemicals.
G
No guarantee claims for the camera and no liability for
any resulting personal damage or material damage will
be accepted if the camera is used for other purposes
than originally intended, if it is not correctly installed or
if it is not repaired in an expert way.
If the camera is to be put out of operation defin-
itively, take it to a local recycling plant for a dis-
posal which is not harmful to the environment.
®
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
HDCAM-650
3 Installation
1) To find the optimum place of mounting, make a test
run.
2) At the location of mounting, drill three holes for fixing
the base (3) and, if necessary, drill a hole for the con-
nection cable (the cable can also be guided through
the cable inlet at the side of the base). If necessary,
loosen the setscrews (2) of the base and the camera
support, using the hex key supplied.
3) Use a 75 Ω cable to connect the BNC jack (13) to the
SDI video input of a monitor. The maximum cable
length possible depends on the cable quality. With the
low-loss special cable KHD-1 from MONACOR, the
maximum cable length is 170 m. Repeaters (e. g.
HDEXT-206) can be inserted to support cable lengths
of several hundred meters.
4) To make the menu settings, remove the cap (7) of the
service connection; the control lever (9) is located
beneath the cap.
For testing purposes, an additional analog low-
resolution video signal is available at the jack (8).
To connect a monitor, connect the plug (10) of the
adapter cable "EXTRA VIDEO" to the jack and the
RCA plug (11) to the input of the monitor.
5) Connect a regulated 12 V power supply with a perma-
nent rating of 1 A to the inline jack (12). A low-voltage
plug 5.5 / 2.1 mm (exterior / interior diameter) is re -
quired. Make absolutely sure to observe the correct
polarity (centre contact = +).
CAUTION The infrared LEDs switch on in case of
darkness. When setting up the camera, never look
directly into the lit infrared LEDs from a close range.
The infrared light may cause eye irritation. However,
the infrared radiation is far below the emission limit
and rated risk-free according to EN 62471.
6) Please observe the following for outdoor installations:
The connections (12, 13) and the cable splitter (4) are
not weatherproof and must be protected accordingly.
7) Switch on the monitor connected and align the camera
by means of the monitor image: Loosen the setscrews
(2), using the hex key supplied, and position the cam-
era as desired. Then tighten the screws again. Posi-
tion the sunshield (1) on the camera as required.
Use the zoom ring (5) to adjust the angle of view
and the focus ring (6) to focus the image on the moni-
tor. To make the adjustments, loosen the screw on the
corresponding ring; retighten the screw when the
adjustments have been completed.
Order No. 18.3730
4 Adjustments via the On-screen Menu
The on-screen menu is operated by means of the control
lever (9). To display the on-screen menu, press the con-
trol lever. The main menu appears:
MENU
EXPOSURE
WHITE BAL
DAY&NIGHT
BACKLIGHT
3D-DNR
IMAGE
MONITOR
SYSTEM
EXIT
To select a menu item, tilt the lever vertically ; to change
the value or to select an option, tilt the lever horizontally
↵
. When the symbol
appears behind a menu item or
option, the lever can be pressed to call up a submenu or
to activate a function.
Please refer to the reverse page of these instructions for
a tabulated list of all available setting options.
EXIT
To exit the menu, select the line
and press the lever.
Copyright
©
by MONACOR INTERNATIONAL. All rights reserved.
5 Specifications
Image sensor: . . . . . . . . . CMOS chip, 8.5 mm (
2 megapixels, progressive
scan
Number of pixels: . . . . . . . 1920 × 1080 max.
Lens: . . . . . . . . . . . . . . . . 6 – 50 mm/ 1 : 1.4
controllable iris (DC)
Minimum illumination: . . . 0.1 lx (colour)
SDI video formats: . . . . . . 1080p30, 1080p25,
720p60, 720p50
Analog video output: . . . . PAL / NTSC, 1Vpp / 75 Ω
S / N ratio: . . . . . . . . . . . . . > 50 dB (AGC off)
±
Power supply: . . . . . . . . . 12 V
10 %, 1 A
Admissible temperature: . -10 to +50 °C
IP rating: . . . . . . . . . . . . . IP 66
Dimensions: . . . . . . . . . . . ∅ 95 mm × 150 mm
Weight: . . . . . . . . . . . . . . . 1.4 kg
Subject to technical modification.
A-1554.99.01.04.2014
1
⁄
")
3
Werbung
