Overview Of The Components; Unpacking The Appliance; Installation And Use; Short-Term Operation - Clatronic KM 3099 Bedienungsanleitung

Overview of the Components

1 Utensil switch
2 Kitchen machine, basis appliance
3 Mixer vessel
4 Mixer vessel lid with fi lling slot
5 Filling slot seal
6 Drive shaft for mixing bowl
7 Safety cover for mixer drive
8 Mixing bowl lid
9 Mixing bowl driveshaft
10 Mixing bowl
11 Grater utensil
12 Cutting utensil
13 Filler tube
14 Utensil holder
15 Metal blade
16 Plastic blade
17 Filler
18 Spatula
19 Cable take-up
20 PULSE button – pulse operation
21 Locating pin
22 Rubber feet

Unpacking the appliance

• Remove the appliance from the box and all the enclosed
accessories.
• Do not through the packaging away, but keep it together with
the inner packing and the warranty documents for the whole
life of the warranty. If you pass this article to others, please
also give them these instructions.
• Place the appliance on smooth, level and stable work
surface.
• Do not insert the appliance plug without installing the
necessary attachments.
• Before the device is used for the fi rst time the mixing bowl,
processor bowl, various lids and other accessories should
be washed in soapy water to remove any contamination
from their production.
WARNING:
Some parts are extremely sharp! There is the risk of being
injured under certain circumstances!
• Clean each single part one after the other and with great
caution!
• Dry well all the parts after washing.

Installation and use

Make sure that the switch (1) is positioned on „0" and that the
appliance plug is not inserted when changing the attachments.
Only now can the attachments be mounted and used.
The safety cover (7) has to be mounted on the drive shaft of
the mixer drive (6) when you operate the grater bowl in order to
avoid any injuries.
The appliance cannot be used without the safety lid!
05-KM 3099 41
• Short-term
operation: The mixer is also suitable for short-term
operation of not more than 2 minutes.
After this time it should be switched off.
• Pulse operation: Pulse operation is achieved by pressing
the button briefl y and then releasing it
again. The mixture should be used in
this mode for not more than 2 minutes.
Please allow it to cool down for 2
minutes before using it again!
Operation
Positioning the Mixing Bowl and Lid
Please all parts before using for the fi rst time (see „Cleaning").
1. Place the mixing bowl (3) on the base of the device in such
a way that the „ " mark on the bottom edge of the bowl
points to the „ " arrow on the base of the device. Then turn
the mixing bowl clockwise until both are marks aligned with
one another.
2. The „ " arrow on the edge of the lid (4) points to the right-
hand „ " mark on the mixing bowl.
3. Then turn the lid in the direction of the arrow „
mark on the lid is now pointing to the left-hand „ " mark of
the mixing bowl. The mechanisms on the lower edge of the
lid and the upper edge of the container must mesh with one
another (Illustration 2).
Assembly of mixing bowl and lid
Please all parts before using for the fi rst time (see „Cleaning").
1. Place the bowl (10) on the base in such a way that the left
„ " mark on the bowl is pointing to the lower „ " mark on
the base. Then turn the bowl clockwise until you hear it lock
into place (Illustration 3 + 4).
2. Put the locating pin (21) over the drive shaft (Illustration
5) and select the corresponding tool (see the section on
„Grater Bowl Operation").
3. Position the lid (8) in such a way that the arrow „ " on the
lid is aligned with the right-hand mark „ " on the grater
bowl. The metal tip of the locating pin (21) has to engage
into its bearing in the lid. Then turn the lid in the direction of
the „ " until it is heard to lock into place at the stop. To
remove the lid, turn it in an anticlockwise direction.
Position the cover for the mixer drive (7) on the drive shaft of the
mixing vessel (6) such that the „ " mark on the cover is pointing
to the „ " arrow on the base of the device. Turn the cover for the
mixer drive in a clockwise direction as far as it will go.
Double Safety System
The motor can only be switched on if the grater bowl with the
cover locks into place correctly and the cover for the mixer drive
(7) is mounted. The mixer can only be used if the grater bowl
is correctly positioned. You should only remove the lid from
the grater bowl or from the mixing vessel when the device is
switched off.
". The „ "
41
05.10.2006, 11:05:33 Uhr