General Safety Instructions; Overview Of The Components; Instruction Manual; Special Safety Instructions - Clatronic km 2717 Bedienungsanleitung

General Safety Instructions

Read the operating instructions carefully before putting the
appliance into operation and keep the instructions including the
warranty, the receipt and, if possible, the box with the internal
packing.
• The appliance is designed exclusively for private use
and for the envisaged purpose. This appliance is not fi t
for commercial use. Do not use it outdoors (except if it is
designed to be used outdoors). Keep it away from sources
of heat, direct sunlight, humidity (never dip it into any liquid)
and sharp edges. Do not use the appliance with wet hands.
If the appliance is humid or wet, unplug it immediately. Do
not put it in water.
• When cleaning or putting it away, switch off the appliance
and always pull out the plug from the socket (pull on the
plug, not the cable) if the appliance is not being used and
remove the attached accessories.
• Do not operate the machine without supervision. If you
should leave the workplace, always switch the machine off
or remove the plug from the socket (pull the plug itself, not
the lead).
• Check the appliance and the cable for damage on a regular
basis. Do not use the appliance if it is damaged.
• Do not try to repair the appliance on your own. Always
contact an authorized technician. To avoid the exposure
to danger, always have a faulty cable be replaced only by
the manufacturer, by our customer service or by a qualifi ed
person and with a cable of the same type.
• Use only original spare parts.
• Pay careful attention to the following "Special Safety Instruc-
tions".
Children
• In order to ensure your children's safety, please keep all
packaging (plastic bags, boxes, polystyrene etc.) out of their
reach.
Caution! Do not allow small children to play with the foil as
there is a danger of suffocation!
• To protect children from the dangers posed by electrical
appliances, make sure that the cable is hanging low and that
children do not have access to the appliance.

Special safety instructions

• WARNING: The cutter and grater attachments, the chopper
and the French fry slicer have extremely sharp cutting
and grating surfaces and edges! When removing the
attachments from the bowl and container you will come into
contact with this accessory. Handle this accessory with care
to avoid injuries.
• Before changing the attachments, the appliance must be
disconnected from the mains!
• Do not reach into the mixer vessel as the underlying blade
may cause injuries under certain circumstances!
• The appliance is equipped with a safety switch. Do not use
the appliance in case of malfunctions or if the safety switch
has been tampered with!
• Do not remove the lid during use.
05-KM 2717 N4 25
• Switch on the appliance only once the presser in the
opening of the lid is inserted.
• Use only the supplied presser to press the food. Do not
use your fi ngers, forks or other objects to avoid injuries or
damage.
• Do not use the appliance when empty.
• Do not carry or lift the appliance during use. Always switch
it off fi rst and pull out the plug. Carry the appliance always
with both hands!
• Clean the appliance only as described in „Cleaning".

Overview of the Components

1 Utensil switch
2 Kitchen machine, basis appliance
3 Mixer vessel
4 Mixer vessel lid with fi lling slot
5 Filling slot seal
6 Disk for chips
7 Grating disk
8 Mixing bowl lid
9 Mixing bowl driveshaft
10 Mixing bowl
11 Grater utensil
12 Cutting utensil
13 Filler tube
14 Utensil holder
15 Metal blade
16 Plastic blade
17 Filler
18 Spatula
19 Mixer lid
20 Accessory drawer
21 Locating pin
Operation of machine
Assembly of mixing bowl and lid
Please all parts before using for the fi rst time (see „Cleaning").
1. Place the bowl (10) on the base (2) in such a way that the
left mark on the bowl is pointing to the lower ▲ mark on
the base. Then turn the bowl clockwise until you hear it lock
into place. The right mark of the bowl is now pointing to
the ▲ mark on the base.
2. Place a tool (14, 15, 16) on the drive axle.
3. Press the equipment you wish to use (grating or cutting
attachments) - to be found in the accessories drawer (20)
- as far as it will go on to the device holder (14).
4. When the tool holder (14) is selected the guide mandrel (21)
must be attached. The metal point faces upwards.
5. Place the lid on the bowl (8) so that the left arrow on the
lid is in line with the ▲ mark on the bowl. The metal tip of
the locating pin (21) has to engage into its bearing in the lid.
Then turn the lid clockwise until the protruding section on
the lid is heard to lock into place in the safety lock opening
on the base of the machine. Now the right mark on the lid
is pointing to the ▲ mark on the bowl. To remove the lid,
turn it in an anticlockwise direction.
25
02.05.2006, 11:58:01 Uhr