Inhaltsverzeichnis; Safety; Description - Lincoln B Serie Bedienungsanleitung

FlowMaster™ Rotary Driven Hydraulic Pump
Table of Contents
Safety .................................................................................2
Description...................................................................................2
Appropriate Use................................................................2
Pump Performance and Specifi cations..............................3
Installing the Pump.....................................................................4
Operation.....................................................................................5
Maintenance and Repair...........................................................5
Pump Dimensions.............................................................7
Repair Parts List............................................................................9
Trouble Shooting........................................................................10

Safety

Read and carefully observe these operating instructions before
unpacking and operating the pump! The pump must be oper-
ated, maintained and repaired exclusively by persons famil-
iar with the operating instructions. Local safety regulations
regarding installation, operation and
maintenance must be followed.
Operate this pump only after safety instructions and this ser-
vice manual are fully understood.
Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
Safety Instructions
This equipment generates very high grease pressure. Ex-
treme caution should be used when operating this equipment
as material leaks from loose or ruptured
components can inject fl uid through the skin and into the body
causing serious bodily injury. Adequate protection is recom-
mended to prevent splashing of material onto the skin or into
the eyes.
If any fl uid appears to penetrate the skin, get emergency
medical care immediately. Do not treat as a simple cut. Tell
attending physical exactly what fl uid was injected.
Inspection
If overpressurizing of the equipment is believed to have oc-
curred, contact the factory authorized warranty and service
center nearest you for inspection of the pump.
Specialized equipment and knowledge is required for repair
of this pump. Contact the factory authorized warranty and
service center nearest you for repair or adjustments other than
maintenance specifi ed in this manual.
Page Number - 2
Annual inspection by the factory authorized warranty and service
center nearest you is recommended.
Page
A list of factory authorized warranty and service centers is avail-
able upon request.
Damaged Pumps
Any pump that appears to be damaged in any way, is badly worn
or operates abnormally, shall be removed from use until repairs
are made. Contact the factory authorized warranty and service
center nearest to you for repairs.
A newer version of the FlowMaster pump was introduced in
June of 2008. These units incorporate the following improve-
ments:
* Bushing & plunger seals used along with elastomer cup seals
for longer life and better high temperature operation.
* A crankcase oil dipstick
* Hardened and ground section on the reciprocating tube for
longer life and better crankcase oil control.
* Hardened and ground pivot pin bushings with a tighter fi t into
the pivot pin anchor.
* Improved pivot pin fastener with deeper Allen hex socket.
All of the improved parts can be used with the older model
pumps, so the upgraded parts and subassemblies will now be
supplied to repair older model pumps. Please see the "Main-
tenance and Repair" section for a list of the new repair kits and
their proper application.
85480 - Pump for 120 pound drum (16 gallon)
85481 - Pump for 60 pound drum
85482 - Pump for 400 pound drum (55 gallon)
85483 - Pump for 5 gallon pail
85247 - Similar to 85480, but with a manual override
85610 - Low Temperature Pump for 400 lb. drum (55 gallon)
85586 - Heavy Duty pump for 400 lb. drum
274055 - Same as 85481 with Solenoid Cable Assembly
General Description
The Lincoln Industrial rotary Hydraulic Pump is a fully hydrauli-
cally operated grease pump. Grease output is proportional to
the hydraulic input fl ow. The pump is primarily designed for
centralized lubrication systems such as the Single Line parallel,
Single Line Progressive and Two Line systems. An integrated
pump control manifold is incorporated with the motor to control
input fl ow and pressure. A 24 volt DC solenoid valve is also in-
corporated as a method to turn the pump on and off. A 24 volt
DC solenoid valve with a manual override is standard on model
85247 and is an option on other models.
The pump is driven by the rotary motion of the hydraulic motor.
Rotary motion is converted to reciprocating motion through an
eccentric crank mechanism. The reciprocating action causes
the pump cylinder to move up and down. The unit is a positive
displacement double acting pump as grease output occurs dur-
ing both the up and down stroke.
During the down stroke, the pump cylinder is extended into the
grease. Through the combination of shovel action and vacuum

Description

Form 403626