Optional Accessory - Makita LS002G Betriebsanleitung

Press the workpiece flat against the guide fences and
the turn base. Position the workpiece at the desired
cutting position and secure it firmly by tightening the
vise knob.
► Fig.42: 1. Holes 2. Vise rod 3. Vise arm 4. Clamping
screw 5. Vise knob
Horizontal vise

Optional accessory

WARNING:
Always rotate the nut holder
clockwise until the workpiece is properly secured.
If the workpiece is not properly, secured the material
may move during the cutting operation causing pos-
sible damage to the circular saw blade, causing the
material to be thrown and loss of control resulting in
serious personal injury.
WARNING:
When cutting a thin workpiece,
such as base boards, against the fence, always
use the horizontal vise.
CAUTION:
When cutting the workpiece of the
thickness 20 mm or thinner, make sure to use a
spacer block to secure the workpiece.
The horizontal vise can be installed either on the left or
on the right side of the base. When performing 22.5° or
greater miter cuts, install the horizontal vise on the side
opposite to the direction in which the turn base is to be
turned.
By flipping the nut holder counterclockwise, the vise
is released, and rapidly moves in and out. To grip the
workpiece, push the vise knob forward until the vise
plate contacts the workpiece and flip the nut holder
clockwise. Then turn the vise knob clockwise to secure
the workpiece.
► Fig.43: 1. Vise plate 2. Nut holder 3. Vise knob
NOTE: The maximum width of workpiece which can
be secured by the horizontal vise is 68 mm.
Sub base
WARNING:
Always support a long workpiece
so it is level with the top surface of the turn base
for an accurate cut and to prevent dangerous loss
of tool control. Proper workpiece support will help
avoid blade pinch and possible kickback which may
result in serious personal injury.
WARNING:
Before the cutting operation,
always be sure that the sub bases are secured by
the screws.
To hold long workpieces horizontally, sub bases are
provided on both sides of the tool. Loosen the screws
and extend the sub bases to the appropriate length for
holding the workpiece. Then tighten the screws.
► Fig.44: 1. Sub base 2. Screw
When cutting, place the workpiece flat against the guide
fences.
► Fig.45: 1. Guide fence 2. Sub base
OPERATION
This tool is intended to cut wood products. With appropriate Makita
genuine saw blades, following materials can also be sawed :
— Aluminum products
Refer to our website or contact your local Makita dealer for the
correct circular saw blades to be used for the material to be cut.
WARNING:
is not contacting the workpiece, etc. before the
switch is turned on. Turning the tool on with the
circular saw blade in contact with the workpiece may
result in kickback and serious personal injury.
WARNING:
raise the circular saw blade until it has come to a
complete stop. The raising of a coasting blade may result
in serious personal injury and damage to the workpiece.
WARNING:
as turning grip, levers, stopper pin on the tool while the
circular saw blade is rotating. Adjustment while the circular
saw blade is rotating may result in serious personal injury.
NOTICE:
Before use, be sure to unlock the stopper
pin and release the handle from the lowered position.
NOTICE:
Do not apply excessive pressure on the han-
dle when cutting. Too much force may result in overload of
the motor and/or decreased cutting efficiency. Press down
handle with only as much force as necessary for smooth
cutting and without significant decrease in blade speed.
NOTICE:
Gently press down the handle to per-
form the cut. If the handle is pressed down with force
or if lateral force is applied, the circular saw blade
may vibrate and leave a mark (saw mark) in the work-
piece and the precision of the cut may be impaired.
NOTICE:
During a slide cut, gently push the carriage
toward the guide fences without stopping. If the carriage
movement stops during the cut, a mark may be left in the
workpiece and the precision of the cut may be impaired.
Press cutting
WARNING:
of the carriage when performing a press cutting.
Cutting without lock may cause possible kickback
which may result in serious personal injury.
Workpieces up to 70 mm high and 92 mm wide can be
cut in the following manner.
1. Push the carriage toward the guide fences until it
stops and lock it with the stopper pin.
2.
Secure the workpiece with the proper type of vise.
3.
Switch on the tool without the circular saw blade
making any contact and wait until the circular saw blade
attains full speed before lowering.
4. Gently lower the handle to the fully lowered posi-
tion to cut the workpiece.
5. When the cut is completed, switch off the tool and
wait until the circular saw blade has come to a com-
plete stop before returning the circular saw blade to its
fully elevated position.
► Fig.46: 1. Stopper pin
26 ENGLISH
Make sure the circular saw blade
After a cutting operation, do not
Do not perform any adjustment such
Always lock the sliding movement