Specifications - Makita GA7030 Betriebsanleitung

ENGLISH (Original instructions)
1. Shaft lock
2. Motor housing
3. Lock button
4. Handle
5. Switch trigger
6. Lock lever
7. Wheel guard
8. Screw
9. Bearing box
10. Nut
11. Lever
12. Lock nut

SPECIFICATIONS

Model
Depressed center wheel
diameter
Spindle thread
Rated speed (n)/No load speed (n
Overall length
Net weight
Safety class
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects to
the operation of other equipment. With a mains
impedance equal or less than 0.23 Ohms it can be
presumed that there will be no negative effects. The
mains socket used for this device must be protected with
a fuse or protective circuit breaker having slow tripping
characteristics.
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Explanation of general view
13. Depressed center wheel
14. Super flange
15. Inner flange
16. Depressed center wheel/Multi disc
17. Inner flange 102
18. Lock nut wrench
19. Abrasive disc
20. Rubber pad
21. Wire cup brush
22. Wire wheel brush
23. Abrasive cut-off wheel/diamond
wheel
GA7030/GA7030S
180 mm
M14
) 8,500 min
0
511 mm
6.0 kg
ENE048-1
ENF002-2
ENF100-1
GEA010-1
24. Wheel guard for abrasive cut-off
wheel/diamond wheel
25. Outer flange 78
26. Inner flange 78
27. Dust collecting wheel guard
28. Exhaust vent
29. Inhalation vent
30. Commutator
31. Insulating tip
32. Carbon brush
33. Brush holder cap
34. Screwdriver
GA7040S GA9030/GA9030S
-1
6.4 kg
/II
Save all warnings and
instructions for future reference.
GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive Cutting-Off Operations:
1. This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool. Read all
safety warnings, instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
2. Operations such as polishing are not
recommended to be performed with this power
tool. Operations for which the power tool was not
designed may create a hazard and cause personal
injury.
3. Do not use accessories which are not specifically
designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
4. The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated
speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of
GA9040S
230 mm
M14
-1
6,600 min
511 mm
6.3 kg 6.7 kg
GEB033-6
5