Machine Operation; Hopper Dumping; After Machine Use; Pushing/Towing The Machine - Nilfisk-Advance SWEEPER SR 1000S P Betriebsanleitung

Stopping the machine
1. To stop the machine, release the pedal (5, Fig. C).
To stop the machine more quickly, also press the service
brake pedal (6, Fig. C).
In case of emergency, press the emergency push-button
(8, Fig. B) to immediately stop the machine. To
deactivate the emergency push-button (8), turn it
clockwise.
2. To turn off the side brooms (13 and 14, Fig. C), lift them
by using the lever (4).
3. To turn off the main broom (15, Fig. C), the vacuum fan
(19, Fig. U) and the engine, turn the ignition switch (2,
Fig. B) to "0" position.
4. Engage the parking brake according to the following
procedure:
– Press the pedal (6, Fig. C) as necessary, then
engage the brake by turning the lever (7, Fig. C) from
(7b) position to (7a) position.
– Release the pedal (6).
5. Open the hood (10, Fig. C) and close the fuel tap (1, Fig.
V), then close the hood again.

MACHINE OPERATION

1. Avoid stopping for a long time with the machine in the
same position and the brooms rotating: this could create
unwanted marks on the floor.
2. To collect light and bulky debris, lift the front skirt by
pressing the pedal (8, Fig. C); remember that while the
front skirt is lifted, the machine vacuum power
decreases.
CAUTION!
When operating on wet grounds, it is essential
to turn off the vacuum system with the lever (3,
Fig. C) to prevent the dust filter from being
damaged.
3. For machine proper operation, the dust filter must be as
clean as possible. To keep the dust filter clean while
sweeping, turn off the vacuum system with the lever (3,
Fig. C), then press the filter shaker switch (5, Fig. B) for
a while.
After cleaning the filter, turn on the vacuum system with
the lever (3, Fig. C).
While working, repeat the procedure every 10 minutes
on average (depending on the dustiness of the area to
be cleaned).
NOTE
When the dust filter is clogged and/or the
hopper is full, the machine cannot collect dust
and debris anymore.
146 1960 000(2)2006-06 A
The hopper (20, Fig. C) should be dumped after each working
period and whenever it is full (see the procedure in the next
paragraph).
CAUTION!
The engine is equipped with a warning system
to prevent damages to the engine itself in case
the oil quantity in the carter is insufficient.
Before the oil level goes below the safety limit,
the warning system automatically stops the
engine.

HOPPER DUMPING

1. Stop the machine by releasing the drive pedal.
2. Turn the ignition switch (2, Fig. B) to "0" position.
3. Disengage the hook (21, Fig. C) by pulling its lower end.
4. Remove the hopper (20, Fig. C) by using the handle
(22), and dump it into special containers.
5. Reinsert the hopper and fasten it with the hook (21).
6. The machine is ready to start working again.

AFTER MACHINE USE

After working, before leaving the machine:
1. Lift the side brooms with the lever (4, Fig. C).
2. Turn off the vacuum system with the lever (3, Fig. C).
3. Turn on the filter shaker with the switch (5, Fig. B).
4. Turn the ignition switch (2, Fig. B) to "0" position and
remove the key.
5. Close the fuel tap (1, Fig. V) in the compartment (37, Fig.
C).
6. Dump the hopper (20, Fig. C) (see the previous
paragraph).
7. Engage the parking brake according to the following
procedure:
– Press the pedal (6, Fig. C) as necessary, then
engage the brake by turning the lever (7, Fig. C) from
(7b) position to (7a) position.
– Release the pedal (6).

PUSHING/TOWING THE MACHINE

To easily push/tow the machine when it is off, proceed as
follows:
1. Open the hood (10, Fig. C).
2. Turn the switch (27, Fig. U) to "0" position and close the
hood (10, Fig. C).
3. Push or tow the machine.
4. After pushing/towing the machine, turn the switch (27,
Fig. U) back to "I" position.
USER MANUAL
9