Storage And Transportation - 3M 6000 Serie Bedienungsanleitung

STORAGE AND TRANSPORTATION

These products should be stored in the packaging provided in dry, clean conditions away from sources of high
temperature and petrol and solvent vapours. Storage conditions on the packaging refer to Annual Average Temperature
and Relative Humidity values.
indicates acceptable storage conditions. X indicates unacceptable storage conditions. See Figure 4.
Storage under conditions other than those specified by the manufacturer may affect the shelf life.
End of Shelf Life For Single Use Only
[ )
Manufacturer Dispose in accordance with local regulations
J
When stored as stated, the expected shelf life of the product is 5 years from date of manufacture. End of shelf life
(use-by) date is marked on the product and packaging. The original packaging is suitable for transporting the product.
R = Re-usable
NR = Non re-usable (single shift use only)
TECHNICAL SPECIFICATION
3M combination filters generally protect against either single or multiple gas/vapour type(s) and against particulates.
Filter Type Colour Code
A Brown
B Grey
E Yellow
K Green
Formaldehyde Olive green
AX Brown
Hg Red
P White
The 6000 Series gas/vapour filters are also classified, into one of two classes, depending on their capacity to remove
contaminants from the inhaled air
Gas/Vapour Filter Classes
Gas Filter Class NPF 3M™ Half mask*
1 10 (or 1000 ppm (0.1% vol) whichever is
lower)
2 10 (or 1000 ppm (0.5% vol) whichever is
lower)
Particulate Filter NPF 3M™ Half mask*
Class
P3 R 10
Required Minimum Protection Factor (RMPF) - the protection factor required to reduce exposure to an acceptable level.
It is expressed as a ratio of the measured ambient airborne concentration of a contamniant to an acceptable exposure
level or stanard.Please refer to National workplace protection guidance for application of these numbers in the work place
protection factors.
Filter Model Classification
3M™ 6091 A1P3 R
3M™ 6092 A1B1E1K1P3 R + form
3M™ 6095 A2P3 R
3M™ 6096 A1E1HgP3 R
3M™ 6098 AXP3 R
3M™ 6099 A2B2E2K2HgP3 + form
Maximum Use Time 50 hours
(
Type of Contaminant
Organic vapours with boiling point >65°C (with good warning properties) as
specified by the manufacturer
Inorganic Gases & Vapours (with good warning properties) as specified by
the manufacturer
Acid Gases (with good warning properties) as specified by the manufacturer
Ammonia and Organic Ammonia derivatives (with good warning properties)
as specified by the manufacturer
Formaldehyde vapour
Organic vapours with boiling point equal or less than 65°C (with good
warning properties) as specified by the manufacturer
Mercury vapour
Solid and non-volatile liquid aerosols
NPF 3M™ Full Face mask*
50 (or 1000 ppm (0.1% vol) whichever is lower)
100 (or 5000 ppm (0.5% vol) whichever is lower)
NPF 3M™ Full Face mask*
100
Type of Contaminant
Organic vapours with boiling point >65°C (with good warning properties)
as specified by the manufacturer and particulates
Combination organic vapours (boiling.point > 65°C (with good warning
properties), inorganic gases, acid gases, ammonia and formaldehyde up
to 10 ppm and particulates
Organic vapours with boiling point >65°C (with good warning properties)
as specified by the manufacturer and particulates
Organic vapours with boiling point >65°C (with good warning properties)
as specified by the manufacturer and mercury vapour, chlorine, acid
gases and particulates. If used for Hg, maximum use time = 50 hours.
Organic vapours with boiling point <65°C (with good warning properties)
as specified by the manufacturer and particulates
Organic vapours (b.pt>65°C (with good warning properties), inorganic
gases, acid gases, ammonia, formaldehyde up to 10 ppm, mercury
vapour and particulates. If used for Hg, maximum use time = 50 hours.
99
Name and address of
: